Difference between revisions of "CS-MIPI-IMX307 STARVIS Module"
Jump to navigation
Jump to search
| (One intermediate revision by the same user not shown) | |||
| Line 192: | Line 192: | ||
|IRCUT1 | |IRCUT1 | ||
| - | | - | ||
| − | | rowspan="2" | | + | | rowspan="2" |mono |
| rowspan="2" |Full wavelength pass | | rowspan="2" |Full wavelength pass | ||
|- | |- | ||
| Line 270: | Line 270: | ||
|15 | |15 | ||
|3.3VDC | |3.3VDC | ||
| − | | | + | |NC by default，[[Power supply mode switching|<u>How to use</u>]] |
|}<br /> | |}<br /> | ||
==Board Dimension== | ==Board Dimension== | ||
[[File:CS-MIPI-IMX307 CAD drawing.jpg|thumb|600x600px|CS-MIPI-IMX307 CAD drawing / unit : mm|alt=|none]] | [[File:CS-MIPI-IMX307 CAD drawing.jpg|thumb|600x600px|CS-MIPI-IMX307 CAD drawing / unit : mm|alt=|none]] | ||
[[Media:CS-MIPI-IMX307 CAD.dwg|Download dwg file here]] | [[Media:CS-MIPI-IMX307 CAD.dwg|Download dwg file here]] | ||
Revision as of 17:57, 27 March 2020
1 Introduction
CS-MIPI-IMX307 is a high quality Sony STARVIS IMX307 image sensor custom designed add-on board for Raspberry PI.
It attaches to Pi by way of one of the small sockets on the board upper surface and uses the dedicated CSI interface, designed especially for interfacing to cameras.
2 Features
- SONY IMX307 STARVIS Sensor, 1/2.8 inch 2 Mega
- Built-in ISP processing
- CSI-2 Interface
- Uncompressed UYVY format, YUV422-8bit
- Standard lens mount
- IR-CUT circuit
- BLC, Digtal WDR, 2D/3D noise reduction, Anti-fog
- Brightness, Contrast, Sharpness, Saturation adjustable
- Support firmware upgrade via USB disk
- Support Raspberry PI, FPGA, ZYNQ, RK3288, RK3399, JETSON NANO,TX2
3 Technical Detail
| Technical Details | |
| SENSOR | |
| Sensor | SONY IMX307LQD-C STARVIS |
| Pixels | 2.07M pixels |
| Resolution | 1920*1080 |
| Image Size | Diagonal 6.46 mm (Type 1/2.8) |
| Unit Cell Size | 2.9um (H)*2.9um(V) |
| SNR1s Value | 0.24lx |
| ISP | |
| Frame Rate | 1080p@25fps / 30fps, 720p@60fps / 50fps |
| Exposure | Auto or Manual |
| White Balance | Auto or Manual |
| Shutter | 1/25(1/30)s to 1/50,000s |
| Slow Shutter | Coming Soon |
| Denoising | 2D/3D noise reduction |
| Image Setting | Brightness, Contrast, Sharpness, Saturation,Flip, Mirror |
| Image Enhancement | BLC, Digtal WDR, Defog |
| Day/Night Switch | Manual or IR-CUT filter with external trigger |
| Lens & IR-CUT | |
| Lens | Support M12*0.5 or M16*0.5 depend on lens mount |
| Lens Mount with IR-CUT | MTV12 or MTV16 |
| Mounting Hole | 2 screw holes with diameter of 2.2mm,20mm Center-to-Center Spacing |
| Interface | |
| Connector | 15PIN FPC, Compatible with Raspberry PI |
| Communication Interface | IIC, 3.3VDC |
| Video Data Interface | CSI-2 : 2 Data Lanes, CSI-2 YUV422-8bit Data Type, Datarate=594Mbps/lane |
| IR-CUT Control | IR-CUT motor control, 3.3VDC |
| Day/Night External Trigger | 3.3VDC to 5VDC compatibility |
| General | |
| Operating Conditions | -10℃~50℃, Humidity 95% or less, non-condensing |
| Power Supply | 5VDC |
| Power Consumption | 5VDC,1.4W |
| Dimension | 38mm*38mm*10mm(not include lens and lens mount) |
4 Interface & Pin list
4.1 J1:Firmware Update
| 1 | VBUS(5V) |
| 2 | D- |
| 3 | D+ |
| 4 | GND |
4.2 J3:Power Input
| 1 | 5VDC IN |
| 2 | GND |
4.3 J4:Day/Night External Trigger
| 1 | IR LED ON | Low level active（Image to MONO），3.3VDC to 5VDC compatibility |
| 2 | GND | |
| 3 | RESERVE |
4.4 J6:IRCUT Control
| 1 | IRCUT1 |
| 2 | IRCUT2 |
| pin | Signal polarity | Image type | Filter position | |
| Mode 1 | IRCUT1 | + | color | Infrared cutoff |
| IRCUT2 | - | |||
| Mode 2 | IRCUT1 | - | mono | Full wavelength pass |
| IRCUT2 | + |
4.5 J7:Trigger IN,Strobe OUT
| 1 | Trigger IN |
| 2 | GND |
| 3 | Strobe OUT |
4.6 J8:CSI-2 Interface
| 1 | GND | |
| 2 | MIPI_L0_N | |
| 3 | MIPI_L0_P | |
| 4 | GND | |
| 5 | MIPI_L1_N | |
| 6 | MIPI_L1_P | |
| 7 | GND | |
| 8 | MIPI_CK_N | |
| 9 | MIPI_CK_P | |
| 10 | GND | |
| 11 | NC | |
| 12 | NC | |
| 13 | SCL | 3.3VDC Level |
| 14 | SDA | 3.3VDC Level |
| 15 | 3.3VDC | NC by default，How to use |
