CS-MIPI-SC132 Data Sheet

From wiki_veye
Jump to navigation Jump to search

查看中文

CS-MIPI-SC132 Data Sheet

1 Introduction

CS-MIPI-SC132 / CS-MIPI-SC132-V2 is a cost-effective CSI-2 (MIPI) interface camera module that uses the SC132GS global shutter MONO CMOS sensor whice is SmartSens Technology‘s SmartGS™ series. CS-MIPI-SC132 / CS-MIPI-SC132-V2 supports trigger mode and video stream mode.

 
CS-MIPI-SC132 TOP
 
CS-MIPI-SC132 BOTTOM
 
CS-MIPI-SC132-V2 TOP
 
CS-MIPI-SC132-V2 BOTTOM

2 Features

  • 1/4 inch 1.3m pixel SmartGS® CMOS sensor
  • Only mono mode is supported
  • Global shutter
  • Built-in ISP image processing
  • CSI-2 data interface
  • Uncompressed UYVY data format, YUV422-8bit data type
  • Standard lens interface
  • Brightness and contrast can be adjusted
  • Support video stream mode
  • Support trigger mode
  • Firmware upgrade via USB flash drive
  • Support Raspberry PI Platform, NVIDIA JETSON Platform

3 Technical Detail

Technical Details
SENSOR
Sensor SmartSens SmartGS® SC132GS
Pixels 1.3M pixels
Resolution 1080H*1280V
Image Size 1/4"
Unit Cell Size 2.7um *2.7um
Output Format RAW MONO
Shutter Type Global shutter
ISP
Frame Rate 1280*1080@max45fps,1280*720@max60fps, 640*480@max120fps

1080*1280@max45fps, 720*1280@max60fps, 480*640@max120fps

Exposure Auto or Manual
Gain Auto or Manual
Shutter ( 0 - 1 / Frame Rate ) second
Image Setting Brightness, Contrast, Gamma, Flip, Mirror
Image Synchronization mode
Free-Run The sensor runs under an autonomous clock system
Soft Trigger The image is triggered by the DRA(Direct Register Access)
Hardware Trigger The image is triggered by an external trigger signal,Support multi-camera synchronization
Lens
Lens MTV12 / MTV16 / CS
Lens Mount M12*P0.5 / M16*P0.5 / CS
Mounting Hole 2 screw holes with diameter of 2.2mm,20mm Center-to-Center Spacing
Interface
Connector 15PIN FPC, Compatible with Raspberry PI,JETSON NANO
Communication Interface IIC, 3.3VDC
Video Data Interface CSI-2 : 2 Data Lane,MIPI CSI-2 DC Specifications
MIPI CLK frequence 297MHz
MIPI Data bandwidth 594Mbps / lane * 2
Data Type YUV422-8bit
General
Operating Conditions

(Bare PCB)

Performance guarantee temperature:-20℃~60℃, Humidity 95% or less, non-condensing

Operating guarantee temperature: -30℃~85℃, Humidity 95% or less, non-condensing

Power Supply 5VDC / 3.3VDC optional,3.3V default
Power Consumption CS-MIPI-SC132:Rate Power 1.16W

/ CS-MIPI-SC132-V2:Rate Power 1.23W,Transient Power 1.32W

Dimension 38mm*38mm*12mm(not include lens and lens mount)

4 Optical Quantum Efficiency

Sensor Quantum Efficiency
SC132GS
 
SC132GS QE

5 Interface & Pin list

 
CS-MIPI-SC132-TOP LAYER
 
CS-MIPI-SC132-BOTTOM LAYER
 
CS-MIPI-SC132-V2-TOP LAYER
 
CS-MIPI-SC132-V2-BOTTOM LAYER
J1 : Firmware Update
Pin NO. NAME Remarks
1 VBUS(5V) Connect the USB upgrade cable & USB disk
2 D-
3 D+
4 GND
J3 : Power Input
Pin NO. NAME Remarks
1 VCC5V Optional power supply. How to use 5V power supply
2 GND
J7 : GPIO
Pin NO. NAME Remarks
1 Trigger In Compatible with 2.5-3.3V level
2 GND
3 Strobe Out 2.5V level
J14 : UART
Pin NO. NAME Remarks
1 UART_TX
2 GND
3 UART_RX
J8 : CSI-2 Interface
Pin NO. NAME Remarks
1 GND
2 MIPI_L0_N
3 MIPI_L0_P
4 GND
5 MIPI_L1_N
6 MIPI_L1_P
7 GND
8 MIPI_CK_N
9 MIPI_CK_P
10 GND
11 NC
12 NC
13 SCL 3.3V Level
14 SDA 3.3V Level
15 VCC3V3 Use by default,How to use 5V power supply

6 Board Dimension

 
CS-MIPI-SC132 CAD FILE / unit:mm
 
CS-MIPI-SC132-V2 CAD FILE / unit:mm

Download CS-MIPI-SC132 dxf file here

Download CS-MIPI-SC132-V2 dxf file here

7 PCBA 3D STP File

Download CS-MIPI-SC132 3D STP file

Download CS-MIPI-SC132-V2 3D STP file

8 Assembly Direction

 
CS-MIPI-SC132 002-dir