VEYE-MIPI-290/327 i2c/zh
1 介绍
目录下总共4个文件，camera_i2c_config、i2c_read、i2c_write、veye_mipi_i2c.sh。
第一次使用需要确认此目录下文件都具备可执行权限。
chmod +x *
2 树莓派配置管脚，非树莓派忽略此步
你需要先运行camera_i2c_config
./enable_i2c_vc.sh
./camera_i2c_config
配置管脚，然后执行veye_mipi_i2c.sh
2.1 camera_i2c_config USAGE
连接树莓派Computer Module情况下，运行
./camera_i2c_config [cameranum]
| cameranum | description |
|---|---|
| 0 | CAM0 |
| 1 | CAM1 |
连接树莓派经典版型情况下，直接运行
./camera_i2c_config
3 veye_mipi_i2c.sh USAGE
./veye_mipi_i2c.sh
Usage: ./veye_mipi_i2c.sh [-r/w] [-f] function name -p1 param1 -p2 param2 -b bus
options:
-r read
-w write
-f [function name] function name
-p1 [param1] param1 of each function
-p2 [param1] param2 of each function
-b [i2c bus num] i2c bus number
4 不同板子上的i2c序号
请参考下面的文章，确定你所需要使用的-b参数。
i2c bus number on different boards
5 功能列表
5.1 devid
./veye_mipi_i2c.sh -r -f devid
| value | description |
|---|---|
| 0x06 | VEYE-MIPI-X serises，IMX327,IMX462,IMX385 |
5.2 hdver
./veye_mipi_i2c.sh -r -f hdver
| value | description |
|---|---|
| 0xXX | Version |
5.3 sensorid
./veye_mipi_i2c.sh -r -f sensorid
Print sensor type and board information.
5.4 wdrmode
./veye_mipi_i2c.sh -r -f wdrmode
./veye_mipi_i2c.sh -w -f wdrmode -p1 [value]
| value | description |
|---|---|
| 0x00 | Back Light Mode OFF |
| 0x01 | Back Light Mode ON, LOW |
| 0x02 | Back Light Mode ON, HIGH |
| 0x03 | DOL WDR Enable |
5.5 videoformat
./veye_mipi_i2c.sh -r -f videoformat
./veye_mipi_i2c.sh -w -f videoformat -p1 [value]
WARNING:THIS FUNCTION MUST BE CALLED BEFORE ANY video applications
| value | description | frame rate |
|---|---|---|
| PAL | PAL(50Hz) | 25fps |
| NTSC | NTSC(60Hz) | 30fps |
5.6 mirrormode
./veye_mipi_i2c.sh -r -f mirrormode
./veye_mipi_i2c.sh -w -f mirrormode -p1 [value]
| value | description |
|---|---|
| 0x00 | Normal |
| 0x01 | Mirror |
| 0x02 | V-Flip |
| 0x03 | Mirror And V-Flip(180 Degree Rotate) |
5.7 denoise
./veye_mipi_i2c.sh -r -f denoise
./veye_mipi_i2c.sh -w -f denoise -p1 [value]
| value | description |
|---|---|
| 0x00 | NR 2D Mode = OFF; NR 3D Mode = OFF |
| 0x01 | NR 2D Mode = OFF; NR 3D Mode = LOW |
| 0x02 | NR 2D Mode = OFF; NR 3D Mode = MIDDLE |
| 0x03 | NR 2D Mode = OFF; NR 3D Mode = HIGH |
| 0x04 | NR 2D Mode = LOW; NR 3D Mode = OFF |
| 0x05 | NR 2D Mode = LOW; NR 3D Mode = LOW |
| 0x06 | NR 2D Mode = LOW; NR 3D Mode = MIDDLE |
| 0x07 | NR 2D Mode = LOW; NR 3D Mode = HIGH |
| 0x08 | NR 2D Mode =MIDDLE; NR 3D Mode = OFF |
| 0x09 | NR 2D Mode =MIDDLE; NR 3D Mode = LOW |
| 0x0A | NR 2D Mode = MIDDLE; NR 3D Mode = MIDDLE |
| 0x0B | NR 2D Mode = MIDDLE; NR 3D Mode = HIGH |
| 0x0C | NR 2D Mode =HIGH; NR 3D Mode = OFF |
| 0x0D | NR 2D Mode =HIGH; NR 3D Mode = LOW |
| 0x0E | NR 2D Mode = HIGH; NR 3D Mode = MIDDLE |
| 0x0F | NR 2D Mode = HIGH; NR 3D Mode = HIGH |
5.8 agc
./veye_mipi_i2c.sh -r -f agc
./veye_mipi_i2c.sh -w -f agc -p1 [value]
含义为增益上限
| value | description |
|---|---|
| 0x00~0x0F | AGC intensity |
5.9 lowlight
./veye_mipi_i2c.sh -r -f lowlight
./veye_mipi_i2c.sh -w -f lowlight -p1 [value]
低照度情况下的降帧（慢快门）设置。在低照度情况下，摄像机模组可以通过配置此参数，延长曝光时间，降低帧率，达到更好的低照度效果。
注意，在运动场景下不适合使用。
| value | description |
|---|---|
| 0x01 | 1/2*(FRAME RATE) |
| 0x03 | 1/4*(FRAME RATE) |
| 0x05 | 1/6*(FRAME RATE) |
| 0x07 | 1/8*(FRAME RATE) |
| 0x09 | 1/10*(FRAME RATE) |
| 0x0B | 1/15*(FRAME RATE) |
| 0x0D | 1/20*(FRAME RATE) |
| 0x0F | 1/25*(FRAME RATE) |
| 0x11 | 1/30*(FRAME RATE) |
| 0x00 | Fixed frame rate (25/30) |
5.10 daynightmode
./veye_mipi_i2c.sh -r -f daynightmode
./veye_mipi_i2c.sh -w -f daynightmode -p1 [value]
| value | description |
|---|---|
| 0xFF | Color Mode |
| 0xFE | Black&White Mode |
| 0xFC | Trigger Mode |
IR-CUT (Infrared cut-off filter) is a mechanical shutter design. It is placed between the lens and the image sensor, and is controlled by a motor or an electromagnet.
IR-CUT has two status: Block or Deliver the infrared.
- Color Mode
Image is Color Mode and IR_CUT status Block infrared.
- Black&White Mode
Image is Black&White Mode and IR_CUT status Deliver infrared.
- Trigger Mode
Trigger pin : J3 pin1 of VEYE-MIPI-327 or J2 pin1 of VEYE-MIPI-IMX327S.
Trigger pin High(3.3~12V),Image is Black&White Mode and IR-CUT status Deliver infrared.
Trigger pin Low(GND),Image is Color Mode and IR-CUT status Bolck infrared.
5.11 ircutdir
./veye_mipi_i2c.sh -r -f ircutdir
./veye_mipi_i2c.sh -w -f ircutdir -p1 [value]
IR_CUT pins control direction. value could be 0 or 1.
5.12 irtrigger
./veye_mipi_i2c.sh -r -f irtrigger
./veye_mipi_i2c.sh -w -f irtrigger -p1 [value]
日夜切换外触发模式引脚的极性设置。
| value | description | remark |
|---|---|---|
| 0x0 | 默认值，参考不同型号datasheet说明。 | 第0bit有效，其他为无关位 |
| 0x1 | 反转。 | 第0bit有效，其他为无关位 |
5.13 mshutter
close AE, use manual shutter
./veye_mipi_i2c.sh -r -f mshutter
./veye_mipi_i2c.sh -w -f mshutter -p1 [value]
value值为曝光时间（单位：s）
value 大于等于0x4B则进入低帧率模式
| value | description |
|---|---|
| NTSC(PAL) | |
| 0x40 | auto mode |
| 0x41 | 1/30 (25) |
| 0x42 | 1/60(50) |
| 0x43 | 1/120(100) |
| 0x44 | 1/240(200) |
| 0x45 | 1/480(400) |
| 0x46 | 1/1000 |
| 0x47 | 1/2000 |
| 0x48 | 1/5000 |
| 0x49 | 1/10000 |
| 0x4A | 1/50000 |
| 0x4B | 1/30 (25) *2 |
| 0x4C | 1/30 (25) *4 |
| 0x4D | 1/30 (25) *6 |
| 0x4E | 1/30 (25) *8 |
| 0x4F | 1/30 (25) *10 |
| 0x50 | 1/30 (25) *15 |
| 0x51 | 1/30 (25) *20 |
| 0x52 | 1/30 (25) *25 |
| 0x53 | 1/30 (25) *30 |
5.14 cameramode
Requirements：hdver >= 0x3
./veye_mipi_i2c.sh -r -f cameramode
./veye_mipi_i2c.sh -w -f cameramode -p1 [value]
| value | description |
|---|---|
| 0x0 | Stream mode |
| 0x1 | Capture mode |
Stream mode: stream output
Caputre mode: output the next frame each capture cmd.
5.15 nodf
Requirements：hdver >= 0x3, effective in Stream mode
Number of dropped frames
It is a method of framerate control, output one frame,discard nodf frames,output next frame, and so on.
actual framerate = original framerate /（1+nodf）
For example，if the original framerate is 30fps, set nodf to 2, then actual framerate is 10fps.
./veye_mipi_i2c.sh -r -f nodf
./veye_mipi_i2c.sh -w -f nodf -p1 [value]
ntof range is [0-0xFF]， default 0.
5.16 capture
Requirements：hdver >= 0x3, effective in Capture mode
./veye_mipi_i2c.sh -w -f capture
Output the next frame. This cmd does not interfere the sensor, it just output the next frame (the newest frame).
So it is not trigger mode, there will be a delay[0,1/framerate] between the cmd and the frame exposure.
It is applicable to those that do not require a high level of real-time performance.
5.17 csienable
Requirements：hdver >= 0x3
./veye_mipi_i2c.sh -r -f csienable
./veye_mipi_i2c.sh -w -f csienable -p1 [value]
| value | description |
|---|---|
| 0x0 | suspend csi output |
| 0x1 | enable csi output |
default: 0x1
Note: This is not low power mode, the camera is still working.
5.18 brightness
./veye_mipi_i2c.sh -r -f brightness
./veye_mipi_i2c.sh -w -f brightness -p1 0x32
AE的目标亮度，范围[0,0x64]
5.19 aespeed
./veye_mipi_i2c.sh -r -f aespeed
./veye_mipi_i2c.sh -w -f aespeed -p1 0x32 -p2 0x32
AE 调节速度p1为agc速度，p2为shutter速度，由慢到快[0,0x64]
5.20 contrast
./veye_mipi_i2c.sh -r -f contrast
./veye_mipi_i2c.sh -w -f contrast -p1 0x32
图像对比度，范围[0,0xFF],默认为0x80
5.21 saturation
./veye_mipi_i2c.sh -r -f saturation
./veye_mipi_i2c.sh -w -f saturation -p1 0x32
饱和度,范围: [0,0x64]
5.22 sharppen
./veye_mipi_i2c.sh -r -f sharppen
./veye_mipi_i2c.sh -w -f sharppen -p1 [val1] -p2 [value]
| param1 value | description |
|---|---|
| 0x0 | sharppen disable |
| 0x1 | sharppen enable |
default: 0x1
param2: sharppen strength, range [0x0-0xA]
5.23 wdrtargetbr
./veye_mipi_i2c.sh -r -f wdrtargetbr
./veye_mipi_i2c.sh -w -f wdrtargetbr -p1 0x80
宽动态模式下的整体亮度目标值。
WDR模式生效，[0-0xFF]默认值0x80，WDR模式下，值越大，亮度越高。
5.24 wdrbtargetbr
./veye_mipi_i2c.sh -r -f wdrbtargetbr
./veye_mipi_i2c.sh -w -f wdrbtargetbr -p1 0x80
宽动态模式下的亮区亮度目标值。
WDR模式生效，[0-0xFF],默认值为0x30，值越大，亮区越亮。
此参数的效果与实际场景有关，会存在一个[0-X]的无效区，X与实际场景有关。
并不是说调整为0，则亮区会变黑。
5.25 boardmodel
./veye_mipi_i2c.sh -r -f boardmodel
Requirment: hdver >=4.
读取板子的板号，可以通过此功能区分VEYE-MIPI-327和VEYE-MIPI-IMX327S。
5.26 i2cwen
./veye_mipi_i2c.sh -r -f i2cwen
./veye_mipi_i2c.sh -w -f i2cwen -p1 [0/1]
Requirment: hdver >=4.
是否使能摄像头的i2c写寄存器功能，默认为使能。用于特殊情况下的寄存器写保护。
5.27 i2cauxenable
./veye_mipi_i2c.sh -r -f i2cauxenable
./veye_mipi_i2c.sh -w -f i2cauxenable -p1 [0/1]
Requirment: hdver >=4.
是否使能辅助i2c，如使能辅助i2c,在FFC排线上的主i2c不能使用。用于特殊情况下的总线冲突解决。
5.28 awbgain
./veye_mipi_i2c.sh -r -f awbgain
读取当前白平衡的Rgain和Bgain，参数范围[0,0xFF]。
5.29 wbmode
./veye_mipi_i2c.sh -r -f wbmode
./veye_mipi_i2c.sh -w -f wbmode -p1 [value]
读取当前wb模式
| value | description |
|---|---|
| 0x18 | Auto white balance |
| 0x1B | Manual white balance |
5.30 mwbgain
./veye_mipi_i2c.sh -r -f mwbgain
./veye_mipi_i2c.sh -w -f mwbgain -p1 [rgain] -p2 [bgain]
手动白平衡下的rgain和bgain读写。rgain和bgain的范围[0,0xFF]。
5.31 yuvseq
./veye_mipi_i2c.sh -w -f yuvseq -p1 YUYV
./veye_mipi_i2c.sh -w -f yuvseq -p1 UYVY
./veye_mipi_i2c.sh -r -f yuvseq
配置摄像头的yuv顺序。
Note: only supported on hdver >= 0x4.