CS-MIPI-X i2c - Revision history

Ezcam: /* hdver */

2023-08-18T06:37:45Z

hdver

Xumm: /* pickmode */

2023-04-26T08:33:45Z

pickmode

Admin: /* tgdebncr */

2022-03-30T02:33:49Z

tgdebncr

Admin: /* Introduction */

2022-03-07T09:33:44Z

Introduction

Admin: /* Introduction */

2022-02-27T05:55:43Z

Introduction

Admin: /* streammode */

2021-10-27T07:19:34Z

streammode

Admin: /* mwbgain */

2021-09-08T01:46:07Z

mwbgain

Admin: /* slowshuttergain */

2021-04-29T02:11:07Z

slowshuttergain

Admin: /* expostate */

2021-03-22T12:39:30Z

expostate

Admin: add direct manual exposure modedirect

2021-03-22T12:37:56Z

add direct manual exposure modedirect

@@ Line 72: / Line 72: @@
 |}
 =====hdver=====
-<code>./veye_mipi_i2c.sh -r -f hdver</code>
+<code>./cs_mipi_i2c.sh -r -f hdver</code>
 get hardware logic version

@@ Line 564: / Line 564: @@
 Trigger delay in Hardware Trigger mode (us).<br />note: Only CS-MIPI-SC132 Support.
 =====pickmode=====
-<code>./cs_mipi_i2c.sh -w -f pickmode -p1 enable</code>
+<code>./cs_mipi_i2c.sh -w -f pickmode -p1 [0/1]</code>
 <code>./cs_mipi_i2c.sh -r -f pickmode</code>

@@ Line 550: / Line 550: @@
 =====tgdebncr=====
-<code>./cs_mipi_i2c.sh -w -f triggeredge -p1 enable -p2 [value]</code>
+<code>./cs_mipi_i2c.sh -w -f tgdebncr -p1 enable -p2 [value]</code>
-<code>./cs_mipi_i2c.sh -r -f triggeredge</code><br />In Hardware Trigger mode，the debouncer attribute of the trigger signal.
+<code>./cs_mipi_i2c.sh -r -f tgdebncr</code><br />In Hardware Trigger mode，the debouncer attribute of the trigger signal.
 Any trigger signal that is less than value (us) will be ignored.

@@ Line 22: / Line 22: @@
 <code>./camera_i2c_config</code>
-*for RPI Computer Module
+*for RPI Computer Module 3
 <code>./camera_i2c_config [cameranum]</code>

@@ Line 59: / Line 59: @@
     -d [i2c addr]                  i2c addr if not default 0x3b
-support functions: devid,hdver,camcap,firmwarever,productmodel,videofmtcap,videofmt,ispcap,i2caddr,streammode,powerhz,
+[[I2c bus number and video node|i2c bus number on different boards]]
+===Functions list===
 =====devid=====
 <code>./cs_mipi_i2c.sh -r -f devid</code>

@@ Line 262: / Line 262: @@
 If powerhz is 50，support 1080p@25，720p@50,vga@130.
-Note: only supported on camcap bit 0 is 1.
+Note: only supported on camcap bit 0 is 1. Streammode is the base, and parameters such as exposure need to be reconfigured after modifying streammode.
 *Trigger mode

@@ Line 477: / Line 477: @@
 <code>./cs_mipi_i2c.sh -r -f mwbgain</code>
-manual  white balance mode, set rgain and dgain manually, ggain is always 1.
+manual  white balance mode, set rgain and bgain manually, ggain is always 1.
 GAIN is 4-bit decimal precision, for example: 0x23 means 2+3/16=2.19.

← Older revision		Revision as of 02:11, 29 April 2021
Line 641:		Line 641:
	Y range: [0-9].		Y range: [0-9].

−	Note: only supported on firmware version >= 2.32<br />	+	Note: only supported on firmware version >= 2.32
		+
		+	===== yuvseq =====
		+	<code>./veye_mipi_i2c.sh -w -f yuvseq -p1 YUYV</code>
		+
		+	<code>./veye_mipi_i2c.sh -w -f yuvseq -p1 UYVY</code>
		+
		+	<code>./veye_mipi_i2c.sh -r -f yuvseq</code>
		+
		+	Set yuv seq of camera.
		+
		+	Note: only supported on firmware version >= 2.38<br />

@@ Line 489: / Line 489: @@
 <code>./cs_mipi_i2c.sh -r -f expostate</code>
-readonly, get the current exposure state.  exposure time, again and dgain.
+readonly, get the current exposure state.  exposure time, again and dgain. direct manual exposure mode invalid.
 =====wbstate=====
 <code>./cs_mipi_i2c.sh -r -f wbstate</code>

@@ Line 38: / Line 38: @@
 ./cs_mipi_i2c.sh
-this shell scripts should be used for CS-MIPI-IMX307!
+this shell scripts should be used for CS-MIPI-X!
 Usage:  ./cs_mipi_i2c.sh [-r/w] [-f] function name -p1 param1 -p2 param2 -p3 param3 -b bus
@@ Line 62: / Line 62: @@
 support functions: devid,hdver,camcap,firmwarever,productmodel,videofmtcap,videofmt,ispcap,i2caddr,streammode,powerhz,
-daynightmode ,hue ,contrast , satu , expostate , wbstate ,expmode , aetarget, aetime,aeagc,metime ,meagain , medgain , awbmode , mwbcolortemp , mwbgain,imagedir,sreg,striggerone,triggeredge,autotgcnt,tgdebncr,tgdly,pickmode,discardfrm,pickone,mipistatus,sysreboot,sysreset,paramsave
+ daynightmode ,hue ,contrast , satu , expostate , wbstate ,expfrmmode,expmode , aetarget, aetime,aeagc,metime ,meagain , medgain,dmetime ,dmeagain , dmedgain  , awbmode , mwbcolortemp , mwbgain,imagedir,sreg,striggerone,triggeredge,autotgcnt,tgdebncr,tgdly,pickmode,pickone,mipistatus,ledstrobe,slowshuttergain,sysreboot,sysreset,paramsave
@@ Line 159: / Line 160: @@
 <code>./cs_mipi_i2c.sh -r -f ispcap</code>
-get camera isp capbility. Will add details later.
+get camera isp capbility.
 =====powerhz=====
 <code>./cs_mipi_i2c.sh -r -f powerhz</code>
@@ Line 337: / Line 350: @@
 : manual exposure
 =====aetarget=====
 <code>./cs_mipi_i2c.sh -r -f aetarget</code>
@@ Line 401: / Line 416: @@
 manual dgain，dB. Effective when '''expmode''' is manual.
 X is the integer part and Y is the decimal part, for example X is 2 and Y is 3 means 2.3dB.