VEYE-MIPI-290/327 i2c/ - Revision history

Xumm: /* camera_i2c_config USAGE */

2024-07-08T00:23:52Z

camera_i2c_config USAGE

2023-10-16T07:30:21Z

sharppen

2023-09-27T06:26:22Z

agc

2023-09-21T08:00:36Z

RaspberryPi Only, Set IO config

2023-05-22T02:27:14Z

lowlight

2023-02-10T06:54:20Z

New function list

2022-12-21T08:18:21Z

new_mgain

2022-12-21T08:13:45Z

mshutter

2022-11-23T01:28:25Z

new_mshutter

2022-11-23T01:28:12Z

新功能

@@ Line 18: / Line 18: @@
 ====camera_i2c_config USAGE====
-*for standard RPI, just run
+*for standard RPI （Legacy mode only）, just run
 <code>./camera_i2c_config</code>

@@ Line 487: / Line 487: @@
 |0x0
 | sharppen disable
 |-
 |0x1

@@ Line 202: / Line 202: @@
 agc indicated max gain of AE mode.
-Agc stands for auto gain control. It is a part of auto exposure, in different light intensity, will try to adjust the gain of sensor to achieve the same image brightness.
+Agc stands for auto gain control. It is a part of auto exposure, in different light intensity, will try to adjust the gain of sensor to achieve the same image brightness. 0xC by default.
 {| class="wikitable"
 !value

@@ Line 38: / Line 38: @@
 ./veye_mipi_i2c.sh
-Usage: ./veye_mipi_i2c.sh [-r/w] [-f] function name -p1 param1 -p2 param2 -b bus
+Usage: ./veye_mipi_i2c.sh [-r/w] [-f] function name -p1 param1 -p2 param2 -b bus -d i2caddr
 options:
@@ Line 54: / Line 54: @@
 -b [i2c bus num] i2c bus number
 === i2c bus number on different board ===
 Please refer to the following article to determine which -b parameter you need to use.

@@ Line 219: / Line 219: @@
 {| class="wikitable"
 !value
-!description
+!minimum fps
 |-
 |0x01

@@ Line 571: / Line 571: @@
 === New function list ===
-The following new features are only supported in versions with ''release time'' later than 2022-11-22.
+The following new features are only supported in camera's firmware versions with ''release time'' later than 2022-11-22.
 ===== paramsave =====

← Older revision		Revision as of 08:18, 21 December 2022
Line 605:		Line 605:

	The new version manual gain, depending on the sensor, accurate to 0.1dB or 0.3dB.		The new version manual gain, depending on the sensor, accurate to 0.1dB or 0.3dB.
		+
		+	===== auto_shutter_max =====
		+	This feature is only supported in versions with ''release time'' later than 2022-12-09.
		+
		+	Configure the upper limit of auto exposure when '''mshutter''' is configured to auto.
		+
		+	<code>./veye_mipi_i2c.sh -r -f auto_shutter_max</code>
		+
		+	<code>./veye_mipi_i2c.sh -w -f auto_shutter_max -p1 1000</code>
		+
		+	in us in the range [1,1000000/fps].
		+
		+	Since the sensor can not support accurate exposure time of 1us, it is recommended to read it for confirmation after configuration.

@@ Line 310: / Line 310: @@
 |}
 =====mshutter=====
-close AE, use manual shutter
+Automatic exposure, manual exposure mode selection and configuration.
 <code>./veye_mipi_i2c.sh -r -f mshutter</code>

@@ Line 570: / Line 570: @@
 Note: only supported on hdver >= 0x4
-==== New function list ====
+=== New function list ===
 The following new features are only supported in versions with ''release time'' later than 2022-11-22.