Difference between revisions of "CS-MIPI-IMX307 STARVIS Module"
Jump to navigation
Jump to search
| Line 124: | Line 124: | ||
[[File:CS-MIPI-IMX307-BIF1.jpg|thumb|CS-MIPI-IMX307-BOTTOM INTERFACE|alt=|700x700px]] | [[File:CS-MIPI-IMX307-BIF1.jpg|thumb|CS-MIPI-IMX307-BOTTOM INTERFACE|alt=|700x700px]] | ||
| − | ===J1:Firmware Update=== | + | ===J1 : Firmware Update=== |
{| class="wikitable" | {| class="wikitable" | ||
|1 | |1 | ||
| Line 140: | Line 140: | ||
|} | |} | ||
| − | ===J3:Power Input=== | + | ===J3 : Power Input=== |
{| class="wikitable" | {| class="wikitable" | ||
|1 | |1 | ||
| Line 151: | Line 151: | ||
|} | |} | ||
| − | ===J4:Day/Night External Trigger=== | + | ===J4 : Day/Night External Trigger=== |
{| class="wikitable" | {| class="wikitable" | ||
|1 | |1 | ||
| Line 166: | Line 166: | ||
|} | |} | ||
| − | ===J6:IRCUT Control=== | + | ===J6 : IRCUT Control=== |
{| class="wikitable" | {| class="wikitable" | ||
|1 | |1 | ||
| Line 200: | Line 200: | ||
| + | | + | ||
|} | |} | ||
| − | ===J7:Trigger IN,Strobe OUT=== | + | ===J7 : Trigger IN,Strobe OUT=== |
{| class="wikitable" | {| class="wikitable" | ||
|1 | |1 | ||
| Line 212: | Line 212: | ||
|} | |} | ||
| − | ===J8:CSI-2 Interface=== | + | ===J8 : CSI-2 Interface=== |
{| class="wikitable" | {| class="wikitable" | ||
|1 | |1 | ||
Revision as of 18:54, 27 March 2020
1 Introduction
CS-MIPI-IMX307 is a highly cost-effective CSI-2 (MIPI) interface camera module, using SONY STARVIS IMX307 image sensor,
built-in excellent ISP image processing, convenient for customers to quickly integrate and release products.
2 Features
- SONY IMX307 STARVIS Sensor, 1/2.8 inch 2 Mega
- Built-in ISP processing
- CSI-2 Interface
- Uncompressed UYVY format, YUV422-8bit
- Standard lens mount
- IR-CUT circuit
- BLC, Digtal WDR, 2D/3D noise reduction, Anti-fog
- Brightness, Contrast, Sharpness, Saturation adjustable
- Support firmware upgrade via USB disk
- Support Raspberry PI Platform, FPGA, ZYNQ,RK3399, NVIDIA JETSON Platform
3 Technical Detail
| Technical Details | |
| SENSOR | |
| Sensor | SONY IMX307LQD-C STARVIS |
| Pixels | 2.07M pixels |
| Resolution | 1920*1080 |
| Image Size | Diagonal 6.46 mm (Type 1/2.8) |
| Unit Cell Size | 2.9um (H)*2.9um(V) |
| SNR1s Value | 0.24lx |
| ISP | |
| Frame Rate | 1080p@25fps / 30fps, 720p@60fps / 50fps |
| Exposure | Auto or Manual |
| White Balance | Auto or Manual |
| Shutter | 1/25(1/30)s to 1/50,000s |
| Slow Shutter | Coming Soon |
| Denoising | 2D/3D noise reduction |
| Image Setting | Brightness, Contrast, Sharpness, Saturation,Flip, Mirror |
| Image Enhancement | BLC, Digtal WDR, Defog |
| Day/Night Switch | Manual or IR-CUT filter with external trigger |
| Lens & IR-CUT | |
| Lens | MTV12 / MTV16 / CS |
| Lens Mount | M12*P0.5 / M16*P0.5 / CS，IRCUT is optional |
| Mounting Hole | 2 screw holes with diameter of 2.2mm,20mm Center-to-Center Spacing |
| Interface | |
| Connector | 15PIN FPC, Compatible with Raspberry PI，JETSON NANO |
| Communication Interface | IIC, 3.3VDC |
| Video Data Interface | CSI-2 : 2 Data Lanes, CSI-2 YUV422-8bit Data Type, Datarate=594Mbps/lane |
| IR-CUT Control | IR-CUT motor control, 3.3VDC |
| Day/Night External Trigger | 3.3VDC to 5VDC compatibility |
| General | |
| Operating Conditions | -10℃~50℃, Humidity 95% or less, non-condensing |
| Power Supply | 5VDC / 3.3VDC optional |
| Power Consumption | 1.4W |
| Dimension | 38mm*38mm*10mm(not include lens and lens mount) |
4 Interface & Pin list
4.1 J1 : Firmware Update
| 1 | VBUS(5V) | Connect the USB upgrade cable & USB storage |
| 2 | D- | |
| 3 | D+ | |
| 4 | GND |
4.2 J3 : Power Input
| 1 | 5VDC IN | use by default. How to use 3.3V power supply |
| 2 | GND |
4.3 J4 : Day/Night External Trigger
| 1 | IR LED ON | Low level active（Image to MONO），3.3VDC to 5VDC compatibility |
| 2 | GND | |
| 3 | RESERVE |
4.4 J6 : IRCUT Control
| 1 | IRCUT1 |
| 2 | IRCUT2 |
| pin | Signal polarity | Image type | Filter position | |
| Mode 1 | IRCUT1 | + | color | Infrared cutoff |
| IRCUT2 | - | |||
| Mode 2 | IRCUT1 | - | mono | Full wavelength pass |
| IRCUT2 | + |
4.5 J7 : Trigger IN,Strobe OUT
| 1 | Trigger IN |
| 2 | GND |
| 3 | Strobe OUT |
4.6 J8 : CSI-2 Interface
| 1 | GND | |
| 2 | MIPI_L0_N | |
| 3 | MIPI_L0_P | |
| 4 | GND | |
| 5 | MIPI_L1_N | |
| 6 | MIPI_L1_P | |
| 7 | GND | |
| 8 | MIPI_CK_N | |
| 9 | MIPI_CK_P | |
| 10 | GND | |
| 11 | NC | |
| 12 | NC | |
| 13 | SCL | 3.3VDC Level |
| 14 | SDA | 3.3VDC Level |
| 15 | 3.3VDC | NC by default，How to use 3.3v power supply |
