Difference between revisions of "CS-MIPI-SC132 Data Sheet"
Jump to navigation
Jump to search
| Line 135: | Line 135: | ||
==Interface & Pin list== | ==Interface & Pin list== | ||
[[File:CS-MIPI-SC132 002.jpg|alt=|thumb|700x700px|CS-MIPI-SC132-TOP LAYER]] | [[File:CS-MIPI-SC132 002.jpg|alt=|thumb|700x700px|CS-MIPI-SC132-TOP LAYER]] | ||
| + | [[File:CS-MIPI-SC132-N004 IF.jpg|alt=|thumb|700x700px|CS-MIPI-SC132-BOTTOM LAYER]] | ||
{| class="wikitable" | {| class="wikitable" | ||
| colspan="3" |'''J1 : Firmware Update''' | | colspan="3" |'''J1 : Firmware Update''' | ||
| Line 256: | Line 257: | ||
|NC by default，[[Power supply mode switching|<u>How to use 3.3V power supply</u>]] | |NC by default，[[Power supply mode switching|<u>How to use 3.3V power supply</u>]] | ||
|} | |} | ||
| + | |||
==Board Dimension== | ==Board Dimension== | ||
[[File:CS-MIPI-SC132 CAD.jpg|alt=|none|thumb|600x600px|CS-MIPI-SC132 CAD FILE / unit：mm]] | [[File:CS-MIPI-SC132 CAD.jpg|alt=|none|thumb|600x600px|CS-MIPI-SC132 CAD FILE / unit：mm]] | ||
Revision as of 18:10, 9 July 2020
CS-MIPI-SC132 Data Sheet
1 Introduction
CS-MIPI-SC132 is a cost-effective CSI-2 (MIPI) interface camera module that uses the SC132GS global shutter MONO CMOS sensor whice is SmartSens Technology‘s SmartGS™ series. CS-MIPI-SC132 supports trigger mode and video stream mode.
2 Features
- 1/4 inch 1.3m pixel SmartGS™ CMOS sensor
- Only mono mode is supported
- Global shutter
- Built-in ISP image processing
- CSI-2 data interface
- Uncompressed UYVY data format, YUV422-8bit data type
- Standard lens interface
- Brightness and contrast can be adjusted
- Support video stream mode
- Support trigger mode
- Firmware upgrade via USB flash drive
- Support Raspberry PI Platform,RK3399, NVIDIA JETSON Platform
3 Technical Detail
| Technical Details | |
| SENSOR | |
| Sensor | SmartSens SmartGS™ SC132GS |
| Pixels | 1.3M pixels |
| Resolution | 1080H*1280V |
| Image Size | 1/4" |
| Unit Cell Size | 2.7um *2.7um |
| Output Format | RAW MONO |
| Shutter Type | Global shutter |
| ISP | |
| Frame Rate | 1280*1080@max45fps，1280*720@max60fps， 640*480@max120fps
1080*1280@max45fps， 720*1280@max60fps， 480*640@max120fps |
| Exposure | Auto or Manual |
| Gain | Auto or Manual |
| Shutter | ( 0 - 1 / Frame Rate ) second |
| Image Setting | Brightness, Contrast, Gamma, Flip, Mirror |
| Image Synchronization mode | |
| Free-Run | The sensor runs under an autonomous clock system |
| Soft Trigger | The image is triggered by the DRA（Direct Register Access） |
| Hardware Trigger | The image is triggered by an external trigger signal，Support multi-camera synchronization |
| Lens | |
| Lens | MTV12 / MTV16 / CS |
| Lens Mount | M12*P0.5 / M16*P0.5 / CS |
| Mounting Hole | 2 screw holes with diameter of 2.2mm,20mm Center-to-Center Spacing |
| Interface | |
| Connector | 15PIN FPC, Compatible with Raspberry PI，JETSON NANO |
| Communication Interface | IIC, 3.3VDC |
| Video Data Interface | CSI-2 : 2 Data Lane，MIPI CSI-2 DC Specifications |
| MIPI CLK frequence | 297MHz |
| MIPI Data bandwidth | 594Mbps / lane * 2 |
| Data Type | YUV422-8bit |
| General | |
| Operating Conditions
(Bare PCB) |
Performance guarantee temperature：-20℃~60℃, Humidity 95% or less, non-condensing
Operating guarantee temperature： -30℃~85℃, Humidity 95% or less, non-condensing |
| Power Supply | 5VDC / 3.3VDC optional |
| Power Consumption | 1.16W |
| Dimension | 38mm*38mm*12mm(not include lens and lens mount) |
4 Optical Quantum Efficiency
| Sensor | Quantum Efficiency |
| SC132GS |
5 Interface & Pin list
File:CS-MIPI-SC132-N004 IF.jpg
CS-MIPI-SC132-BOTTOM LAYER
| J1 : Firmware Update | ||
| Pin NO. | NAME | Remarks |
| 1 | VBUS(5V) | Connect the USB upgrade cable & USB disk |
| 2 | D- | |
| 3 | D+ | |
| 4 | GND | |
| J3 : Power Input | ||
| Pin NO. | NAME | Remarks |
| 1 | VCC5V | use by default. How to use 3.3V power supply |
| 2 | GND | |
| J7 : Multi-function GPIO | ||
| Pin NO. | NAME | Remarks |
| 1 | GPIO0 | Trigger IO |
| 2 | GND | |
| 3 | GPIO1 | Strobe IO |
| J8 : CSI-2 Interface | ||
| Pin NO. | NAME | Remarks |
| 1 | GND | |
| 2 | MIPI_L0_N | |
| 3 | MIPI_L0_P | |
| 4 | GND | |
| 5 | MIPI_L1_N | |
| 6 | MIPI_L1_P | |
| 7 | GND | |
| 8 | MIPI_CK_N | |
| 9 | MIPI_CK_P | |
| 10 | GND | |
| 11 | NC | |
| 12 | NC | |
| 13 | SCL | 3.3V Level |
| 14 | SDA | 3.3V Level |
| 15 | VCC3V3 | NC by default，How to use 3.3V power supply |
6 Board Dimension
7 Assembly Direction
