CS-MIPI-SC132 Data Sheet
CS-MIPI-SC132 Data Sheet
1 Introduction
CS-MIPI-SC132 is a cost-effective CSI-2 (MIPI) interface camera module that uses the SC132GS global shutter MONO CMOS sensor whice is SmartSens Technology‘s SmartGS™ series. CS-MIPI-SC132 supports trigger mode and video stream mode.
2 Features
- 1/4 inch 1.3m pixel SmartGS™ CMOS sensor
- Only black and white mode is supported
- Global shutter
- Built-in ISP image processing
- CSI-2 data interface
- Uncompressed UYVY data format, YUV422-8bit data type
- Standard lens interface
- Brightness and contrast can be adjusted
- Support video stream mode
- Support trigger mode
- Support for dynamic firmware upgrade via USB flash drive
- Support Raspberry PI Platform,RK3399, NVIDIA JETSON Platform
3 Technical Detail
| Technical Details | |
| SENSOR | |
| Sensor | SmartGS™ SC132GS |
| Pixels | 1.3M pixels |
| Resolution | 1080H*1280V |
| Image Size | 1/4" |
| Unit Cell Size | 2.7um (H)*2.7um(V) |
| Shutter Type | Global shutter |
| ISP | |
| Frame Rate | 1280*1080@45fps，1280*720@60fps， 640*480@120fps
1080*1280@45fps， 720*1280@60fps， 480*640@120fps |
| Exposure | 自动/手动 |
| Shutter | ( 0 - 1 / Frame Rate ) second |
| Image Setting | Brightness, Contrast, Gamma, Flip, Mirror |
| Image Synchronization mode | |
| Free-Run | |
| Soft Trigger | |
| Auto Trigger | |
| Hardware Trigger | |
| Lens | |
| Lens | MTV12 / MTV16 / CS |
| Lens Mount | M12*P0.5 / M16*P0.5 / CS |
| Mounting Hole | 2 screw holes with diameter of 2.2mm,20mm Center-to-Center Spacing |
| Interface | |
| Connector | 15PIN FPC, Compatible with Raspberry PI，JETSON NANO |
| Communication Interface | IIC, 3.3VDC |
| Video Data Interface | CSI-2 : 2 Data Lanes |
| General | |
| Operating Conditions
(Bare PCB) |
Performance guarantee temperature：-20℃~60℃, Humidity 95% or less, non-condensing
Operating guarantee temperature： -30℃~85℃, Humidity 95% or less, non-condensing |
| Power Supply | 5VDC / 3.3VDC optional |
| Power Consumption | TBD |
| Dimension | 38mm*38mm*10mm(not include lens and lens mount) |
4 Optical Quantum Efficiency
| Sensor | Quantum Efficiency |
| SC132GS |
5 Interface & Pin list
| J1 : Firmware Update | ||
| Pin NO. | NAME | Remarks |
| 1 | VBUS(5V) | Connect the USB upgrade cable & USB disk |
| 2 | D- | |
| 3 | D+ | |
| 4 | GND | |
| J3 : Power Input | ||
| Pin NO. | NAME | Remarks |
| 1 | VCC5V | use by default. How to use 3.3V power supply |
| 2 | GND | |
| J8 : CSI-2 Interface | ||
| Pin NO. | NAME | Remarks |
| 1 | GND | |
| 2 | MIPI_L0_N | |
| 3 | MIPI_L0_P | |
| 4 | GND | |
| 5 | MIPI_L1_N | |
| 6 | MIPI_L1_P | |
| 7 | GND | |
| 8 | MIPI_CK_N | |
| 9 | MIPI_CK_P | |
| 10 | GND | |
| 11 | NC | |
| 12 | NC | |
| 13 | SCL | 3.3V Level |
| 14 | SDA | 3.3V Level |
| 15 | VCC3V3 | NC by default，How to use 3.3V power supply |