查看中文
CS-MIPI-SC132 Data Sheet
1 Introduction
CS-MIPI-SC132 is a cost-effective CSI-2 (MIPI) interface camera module that uses the SC132GS global shutter MONO CMOS sensor whice is SmartSens Technology‘s SmartGS™ series. CS-MIPI-SC132 supports trigger mode and video stream mode.
2 Features
- 1/4 inch 1.3m pixel SmartGS™ CMOS sensor
- Only mono mode is supported
- Global shutter
- Built-in ISP image processing
- CSI-2 data interface
- Uncompressed UYVY data format, YUV422-8bit data type
- Standard lens interface
- Brightness and contrast can be adjusted
- Support video stream mode
- Support trigger mode
- Firmware upgrade via USB flash drive
- Support Raspberry PI Platform, NVIDIA JETSON Platform
3 Technical Detail
| Technical Details
|
| SENSOR
|
| Sensor
|
SmartSens SmartGS™ SC132GS
|
| Pixels
|
1.3M pixels
|
| Resolution
|
1080H*1280V
|
| Image Size
|
1/4"
|
| Unit Cell Size
|
2.7um *2.7um
|
| Output Format
|
RAW MONO
|
| Shutter Type
|
Global shutter
|
| ISP
|
| Frame Rate
|
1280*1080@max45fps，1280*720@max60fps， 640*480@max120fps
1080*1280@max45fps， 720*1280@max60fps， 480*640@max120fps
|
| Exposure
|
Auto or Manual
|
| Gain
|
Auto or Manual
|
| Shutter
|
( 0 - 1 / Frame Rate ) second
|
| Image Setting
|
Brightness, Contrast, Gamma, Flip, Mirror
|
| Image Synchronization mode
|
| Free-Run
|
The sensor runs under an autonomous clock system
|
| Soft Trigger
|
The image is triggered by the DRA（Direct Register Access）
|
| Hardware Trigger
|
The image is triggered by an external trigger signal，Support multi-camera synchronization
|
| Lens
|
| Lens
|
MTV12 / MTV16 / CS
|
| Lens Mount
|
M12*P0.5 / M16*P0.5 / CS
|
| Mounting Hole
|
2 screw holes with diameter of 2.2mm,20mm Center-to-Center Spacing
|
| Interface
|
| Connector
|
15PIN FPC, Compatible with Raspberry PI，JETSON NANO
|
| Communication Interface
|
IIC, 3.3VDC
|
| Video Data Interface
|
CSI-2 : 2 Data Lane，MIPI CSI-2 DC Specifications
|
| MIPI CLK frequence
|
297MHz
|
| MIPI Data bandwidth
|
594Mbps / lane * 2
|
| Data Type
|
YUV422-8bit
|
| General
|
| Operating Conditions
(Bare PCB)
|
Performance guarantee temperature：-20℃~60℃, Humidity 95% or less, non-condensing
Operating guarantee temperature： -30℃~85℃, Humidity 95% or less, non-condensing
|
| Power Supply
|
5VDC / 3.3VDC optional
|
| Power Consumption
|
1.16W
|
| Dimension
|
38mm*38mm*12mm(not include lens and lens mount)
|
4 Optical Quantum Efficiency
| Sensor
|
Quantum Efficiency
|
| SC132GS
|
|
5 Interface & Pin list
CS-MIPI-SC132-BOTTOM LAYER
| J1 : Firmware Update
|
| Pin NO.
|
NAME
|
Remarks
|
| 1
|
VBUS(5V)
|
Connect the USB upgrade cable & USB disk
|
| 2
|
D-
|
| 3
|
D+
|
| 4
|
GND
|
| J7 : GPIO
|
| Pin NO.
|
NAME
|
Remarks
|
| 1
|
Trigger In
|
Compatible with 2.5-3.3V level
|
| 2
|
GND
|
|
| 3
|
Strobe Out
|
2.5V level
|
| J14 : UART
|
| Pin NO.
|
NAME
|
Remarks
|
| 1
|
UART_TX
|
|
| 2
|
GND
|
|
| 3
|
UART_RX
|
|
| J8 : CSI-2 Interface
|
| Pin NO.
|
NAME
|
Remarks
|
| 1
|
GND
|
|
| 2
|
MIPI_L0_N
|
|
| 3
|
MIPI_L0_P
|
|
| 4
|
GND
|
|
| 5
|
MIPI_L1_N
|
|
| 6
|
MIPI_L1_P
|
|
| 7
|
GND
|
|
| 8
|
MIPI_CK_N
|
|
| 9
|
MIPI_CK_P
|
|
| 10
|
GND
|
|
| 11
|
NC
|
|
| 12
|
NC
|
|
| 13
|
SCL
|
3.3V Level
|
| 14
|
SDA
|
3.3V Level
|
| 15
|
VCC3V3
|
Use by default，How to use 5V power supply
|
6 Board Dimension
CS-MIPI-SC132 CAD FILE / unit：mm
Download dxf file here
7 PCBA 3D STP File
download 3D STP file
8 Assembly Direction
