ADP-MV1 Adapter Board Data Sheet/zh
Adapter Board:ADP-MV1 DATA SHEET
转接板:ADP-MV1数据手册
1 Introduction 产品介绍
ADP-MV1主要用两个功能：
- 将 MV-MIPI-XXX系列工业相机的FPC30接口，转换为FPC15接口。用于适配树莓派（或者与树莓派相同接口）智能平台。
- 将 MV-MIPI-XXX系列工业相机的FPC30接口中的电源，触发输入，用户输出等引脚，转换为易用的2.54插针和连接可靠的MX1.25连接器。方便测试与系统集成。
2 Product Picture 产品图片
| PART NUMBER / 型号 | FRONT VIEW / 正面图片 | BACK VIEW / 背面图片 | FFC CABLE/FFC线缆 |
| ADP-MV1 |
3 Adapter Board Pinlist 引脚说明
| J1: CSI-2 Interface | ||
| Pin NO. 引脚号 | NAME 名称 | Remarks 说明 |
| 1 | GND | |
| 2 | MIPI_L0_N | |
| 3 | MIPI_L0_P | |
| 4 | GND | |
| 5 | MIPI_L1_N | |
| 6 | MIPI_L1_P | |
| 7 | GND | |
| 8 | MIPI_CK_N | |
| 9 | MIPI_CK_P | |
| 10 | GND | |
| 11 | ENABLE | Camera Power Enable |
| 12 | NC | |
| 13 | SCL | 3.3V Level |
| 14 | SDA | 3.3V Level |
| 15 | NC | NC |
| J2：Connect to MV-MIPI-XXX Industry Camera J3
J2: 连接MV-MIPI-XXX系列工业相机 J3 | ||
| Pin NO. 引脚号 | NAME 名称 | Remarks 说明 |
| 1 | GND | |
| 2 | VCC | 5V |
| 3 | VCC | 5V |
| 4 | VCC | 5V |
| 5 | VCC | 5V |
| 6 | GND | |
| 7 | ENABLE | Camera Power Enable |
| 8 | GND | |
| 9 | MIPI_L0_N | Lane 0 Negative |
| 10 | MIPI_L0_P | Lane 0 Positive |
| 11 | GND | |
| 12 | MIPI_L1_N | Lane 1 Negative |
| 13 | MIPI_L1_P | Lane 1 Positive |
| 14 | GND | |
| 15 | MIPI_CK_N | CLK Negative |
| 16 | MIPI_CK_P | CLK Positive |
| 17 | GND | |
| 18 | MIPI_L2_N | Reserved 预留 |
| 19 | MIPI_L2_P | Reserved 预留 |
| 20 | GND | |
| 21 | MIPI_L3_N | Reserved 预留 |
| 22 | MIPI_L3_P | Reserved 预留 |
| 23 | GND | |
| 24 | SCL_MV | I2C SCL, 3.3V Level |
| 25 | SDA_MV | I2C SDA, 3.3V Level |
| 26 | GPIO3 | Reserved 预留 |
| 27 | USER IO2 | Multi-function Port 2，3.3V level；可配置输出2，3.3V电平标准 |
| 28 | USER IO1 | Multi-function Port 1，3.3V level；可配置输出1，3.3V电平标准 |
| 29 | TRIGGER_I | Hardware Trigger in，3.3V level；硬件触发输入，3.3V电平标准 |
| 30 | GND | |
| J3：Auxiliary Expansion Port 1
J3：辅助扩展口1 | |||||
| Pin NO. 引脚号 | NAME 名称 | Remarks 说明 | Pin NO. 引脚号 | NAME 名称 | Remarks 说明 |
| 1 | VCC | 板内连接到 J2-2 | 2 | GND | |
| 3 | TRIGGER_I | 板内连接到 J2-29 | 4 | GND | |
| 5 | USER IO1 | 板内连接到 J2-28 | 6 | GND | |
| 7 | USER IO2 | 板内连接到 J2-27 | 8 | GND | |
| 9 | GPIO3 | 板内连接到 J2-26 | 10 | GND | |
| 11 | SDA_MV | 板内连接到 J2-25 | 12 | SCL_MV | 板内连接到 J2-24 |
| 13 | SDA_USER | 板内连接到 J1-14 | 14 | SCL_USER | 板内连接到 J1-13 |
| 注：
使用 J1-I2C ：短接11-13，同时短接12-14。 使用 其它 I2C ：断开11-13，断开12-14；SDA信号连接J3-11，SCL信号连接J3-12。 | |||||
| J4：Auxiliary Expansion Port 2
J4：辅助扩展口2 | ||
| Pin NO. 引脚号 | NAME 名称 | Remarks 说明 |
| 1 | VCC | 板内连接到 J2-2 |
| 2 | GND | |
| 3 | TRIGGER_I | 板内连接到 J2-29 |
| 4 | USER IO1 | 板内连接到 J2-28 |
| 5 | USER IO2 | 板内连接到 J2-27 |
| 6 | GPIO3 | 板内连接到 J2-26 |
| 7 | GND | |
| 8 | SDA_MV | 板内连接到 J2-25 |
| 9 | SCL_MV | 板内连接到 J2-24 |
| 10 | GND | |
4 Schematic 原理图
5 Adapter Board Dimension 尺寸图
Download dwg file here
下载dwg文件