Line 4: |
Line 4: |
| | | |
| ==Introduction== | | ==Introduction== |
− | CS-MIPI-SC132 is a cost-effective CSI-2 (MIPI) interface camera module that uses the SC132GS global shutter MONO CMOS sensor whice is [http://www.smartsenstech.com/siteweien/enindex.html SmartSens Technology]‘s SmartGS™ series. CS-MIPI-SC132 supports trigger mode and video stream mode. | + | CS-MIPI-SC132 / CS-MIPI-SC132-V2 is a cost-effective CSI-2 (MIPI) interface camera module that uses the SC132GS global shutter MONO CMOS sensor whice is [http://www.smartsenstech.com/siteweien/enindex.html SmartSens Technology]‘s SmartGS™ series. CS-MIPI-SC132 / CS-MIPI-SC132-V2 supports trigger mode and video stream mode. |
− | [[File:CS-MIPI-SC132 001.jpg|alt=|thumb|400x400px|CS-MIPI-SC132 TOP]] | + | [[File:CS-MIPI-SC132-N001.jpg|alt=|thumb|400x400px|CS-MIPI-SC132 TOP]] |
− | [[File:CS-MIPI-SC132 003.jpg|alt=|thumb|400x400px|CS-MIPI-SC132 BOTTOM]] | + | [[File:CS-MIPI-SC132-N002.jpg|alt=|thumb|400x400px|CS-MIPI-SC132 BOTTOM]] |
| + | [[File:CS-MIPI-SC132-V2.0 01.jpg|alt=|thumb|400x400px|CS-MIPI-SC132-V2 TOP]] |
| + | [[File:CS-MIPI-SC132-V2.0 02.jpg|alt=|thumb|400x400px|CS-MIPI-SC132-V2 BOTTOM]] |
| + | |
| ==Features== | | ==Features== |
| | | |
− | *1/4 inch 1.3m pixel SmartGS™ CMOS sensor | + | *1/4 inch 1.3m pixel SmartGS<sup>®</sup> CMOS sensor |
− | *Only black and white mode is supported | + | *Only mono mode is supported |
| *Global shutter | | *Global shutter |
| *Built-in ISP image processing | | *Built-in ISP image processing |
Line 19: |
Line 22: |
| *Support video stream mode | | *Support video stream mode |
| *Support trigger mode | | *Support trigger mode |
− | *Support for dynamic firmware upgrade via USB flash drive | + | *Firmware upgrade via USB flash drive |
− | *Support Raspberry PI Platform,RK3399, NVIDIA JETSON Platform | + | *Support Raspberry PI Platform, NVIDIA JETSON Platform |
| | | |
| ==Technical Detail== | | ==Technical Detail== |
Line 29: |
Line 32: |
| |- | | |- |
| |Sensor | | |Sensor |
− | |SmartGS™ [http://www.smartsenstech.com/siteweien/ensmartGS.html SC132GS] | + | |SmartSens SmartGS<sup>®</sup> [https://smartsens.oss-cn-beijing.aliyuncs.com/web/products/SC132GS_V5.0.pdf SC132GS] |
| |- | | |- |
| |Pixels | | |Pixels |
Line 41: |
Line 44: |
| |- | | |- |
| |Unit Cell Size | | |Unit Cell Size |
− | |2.7um (H)*2.7um(V) | + | |2.7um *2.7um |
| |- | | |- |
| |Output Format | | |Output Format |
Line 52: |
Line 55: |
| |- | | |- |
| |Frame Rate | | |Frame Rate |
− | |1280*1080@45fps,1280*720@60fps, 640*480@120fps | + | |1280*1080@max45fps,1280*720@max60fps, 640*480@max120fps |
− | 1080*1280@45fps, 720*1280@60fps, 480*640@120fps | + | 1080*1280@max45fps, 720*1280@max60fps, 480*640@max120fps |
| |- | | |- |
| |Exposure | | |Exposure |
Line 73: |
Line 76: |
| |- | | |- |
| |Soft Trigger | | |Soft Trigger |
− | |Trigger the photo by the software control register | + | |The image is triggered by the DRA(Direct Register Access) |
− | |-
| |
− | |Auto Trigger
| |
− | |By configuring the control register, the photo is automatically triggered periodically
| |
| |- | | |- |
| |Hardware Trigger | | |Hardware Trigger |
− | |The photo is triggered by an external trigger signal | + | |The image is triggered by an external trigger signal,Support multi-camera synchronization |
| |- | | |- |
| | colspan="2" |'''Lens''' | | | colspan="2" |'''Lens''' |
Line 101: |
Line 101: |
| |- | | |- |
| |Video Data Interface | | |Video Data Interface |
− | |CSI-2 : 2 Data Lanes | + | |CSI-2 : 2 Data Lane,[[MIPI Introduction|''<u>MIPI CSI-2 DC Specifications</u>'']] |
− | [[MIPI Introduction|'''''<u>MIPI CSI-2 DC Specifications</u>''''']] | + | |- |
| + | |MIPI CLK frequence |
| + | |297MHz |
| + | |- |
| + | |MIPI Data bandwidth |
| + | |594Mbps / lane * 2 |
| + | |- |
| + | |Data Type |
| + | |YUV422-8bit |
| |- | | |- |
| | colspan="2" |'''General''' | | | colspan="2" |'''General''' |
Line 112: |
Line 120: |
| |- | | |- |
| |Power Supply | | |Power Supply |
− | |<u>5VDC / 3.3VDC</u> optional | + | |<u>[[Power supply mode switching|5VDC / 3.3VDC]]</u> optional,3.3V default |
| |- | | |- |
| |Power Consumption | | |Power Consumption |
− | |TBD | + | |CS-MIPI-SC132:Rate Power 1.16W |
| + | / CS-MIPI-SC132-V2:Rate Power 1.23W,Transient Power 1.32W |
| |- | | |- |
| |Dimension | | |Dimension |
− | |38mm*38mm*10mm(not include lens and lens mount) | + | |38mm*38mm*12mm(not include lens and lens mount) |
| |} | | |} |
| ==Optical Quantum Efficiency== | | ==Optical Quantum Efficiency== |
Line 129: |
Line 138: |
| |} | | |} |
| ==Interface & Pin list== | | ==Interface & Pin list== |
− | [[File:CS-MIPI-SC132 002.jpg|alt=|thumb|700x700px|CS-MIPI-SC132-TOP LAYER]] | + | [[File:CS-MIPI-SC132 002.jpg|alt=CS-MIPI-SC132-TOP LAYER|thumb|600x600px|CS-MIPI-SC132-TOP LAYER]] |
− | [[File:CS-MIPI-SC132 006.jpg|alt=|thumb|700x700px|CS-MIPI-SC132-BOTTOM INTERFACE]] | + | [[File:CS-MIPI-SC132-N04 IF.jpg|alt=|thumb|600x600px|CS-MIPI-SC132-BOTTOM LAYER]] |
| + | [[File:CS-MIPI-SC132-V2.0 04.jpg|alt=CS-MIPI-SC132-V2-TOP LAYER|thumb|600x600px|CS-MIPI-SC132-V2-TOP LAYER]] |
| + | [[File:CS-MIPI-SC132-V2.0 03.jpg|alt=CS-MIPI-SC132-V2-BOTTOM LAYER|thumb|600x600px|CS-MIPI-SC132-V2-BOTTOM LAYER]] |
| {| class="wikitable" | | {| class="wikitable" |
| | colspan="3" |'''J1 : Firmware Update''' | | | colspan="3" |'''J1 : Firmware Update''' |
Line 160: |
Line 171: |
| |1 | | |1 |
| |VCC5V | | |VCC5V |
− | |use by default. <u>How to use 3.3V power supply</u> | + | |Optional power supply. [[Power supply mode switching|<u>How to use 5V power supply</u>]] |
| + | |- |
| + | |2 |
| + | |GND |
| + | | |
| + | |} |
| + | {| class="wikitable" |
| + | | colspan="3" |'''J7 : GPIO''' |
| + | |- |
| + | |'''Pin NO.''' |
| + | |'''NAME''' |
| + | |'''Remarks''' |
| + | |- |
| + | |1 |
| + | |Trigger In |
| + | |Compatible with 2.5-3.3V level |
| |- | | |- |
| |2 | | |2 |
| |GND | | |GND |
| | | | | |
| + | |- |
| + | |3 |
| + | |Strobe Out |
| + | |2.5V level |
| |} | | |} |
| {| class="wikitable" | | {| class="wikitable" |
− | | colspan="3" |'''J7 : Multi-function GPIO''' | + | | colspan="3" |'''J14 : UART''' |
| |- | | |- |
| |'''Pin NO.''' | | |'''Pin NO.''' |
Line 174: |
Line 204: |
| |- | | |- |
| |1 | | |1 |
− | |GPIO0 | + | |UART_TX |
− | |Multi-function IO | + | | |
| |- | | |- |
| |2 | | |2 |
Line 182: |
Line 212: |
| |- | | |- |
| |3 | | |3 |
− | |GPIO1 | + | |UART_RX |
− | |Multi-function IO | + | | |
| |} | | |} |
| {| class="wikitable" | | {| class="wikitable" |
Line 250: |
Line 280: |
| |15 | | |15 |
| |VCC3V3 | | |VCC3V3 |
− | |NC by default,<u>How to use 3.3V power supply</u> | + | |Use by default,[[Power supply mode switching|<u>How to use 5V power supply</u>]] |
| |} | | |} |
| + | |
| ==Board Dimension== | | ==Board Dimension== |
| + | [[File:CS-MIPI-SC132 CAD new.jpg|alt=|none|thumb|600x600px|CS-MIPI-SC132 CAD FILE / unit:mm]] |
| + | [[File:CS-MIPI-SC132-V21-1213-2D.jpeg|alt=|none|thumb|600x600px|CS-MIPI-SC132-V2 CAD FILE / unit:mm]] |
| + | |
| + | [[Media:CS-MIPI-SC132 CAD v2.dxf.zip|Download CS-MIPI-SC132 dxf file here]] |
| + | |
| + | [[Media:CS-MIPI-SC132-V21-1213-2D.7z|Download CS-MIPI-SC132-V2 dxf file here]] |
| + | |
| + | == PCBA 3D STP File == |
| + | [[Media:3D CS-MIPI-SC132.zip|Download CS-MIPI-SC132 3D STP file]] |
| + | |
| + | [[Media:CS-MIPI-SC132-V21-1213-3D.7z|Download CS-MIPI-SC132-V2 3D STP file]] |
| + | ==Assembly Direction== |
| + | [[File:CS-MIPI-SC132-N003-dir.png|alt=CS-MIPI-SC132 002-dir|left|thumb|800x800px|CS-MIPI-SC132 002-dir]] |