CS-USB-IMX307

From wiki_veye
Jump to navigation Jump to search

查看中文

CS-USB-IMX307 Data Sheet

1 Introduction

CS-USB-IMX307 / CS-USB-IMX307-V2.0 is a cost-effective USB camera. This module use the SONY STARVIS CMOS image sensor IMX307LQD-C,built-in ISP processing.

Users can easily integrate into embedded systems or PC platforms via USB interface.

 
CS-USB-IMX307 TOP
 
CS-USB-IMX307 BOTTOM
 
CS-USB-IMX307-V2.0 TOP
 
CS-USB-IMX307-V2.0 BOTTOM

2 Features

  • SONY IMX307 STARVIS Sensor, 1/2.8 inch 2 Mega
  • Built-in ISP processing
  • USB2.0 Interface,USB Video Class(UVC)
  • Data fromat : YUY2 / MJPG / H.264
  • Standard lens mount
  • IR-CUT circuit
  • Brightness, Contrast, Sharpness, Saturation

3 Thechnical Detail

Technical Details
SENSOR
Sensor SONY IMX307LQD-C STARVIS
Pixels 2.07M pixels
Resolution 1920*1080 MAX
Image Size Diagonal 6.46 mm (Type 1/2.8)
Unit Cell Size 2.9um (H)*2.9um(V)
SNR1s Value 0.24lx
ISP
YUY2 Frame Rate 640*360@25fps / 30fps
MJPG Frame Rate 1920*1080@25fps / 30fps, 1280*720@50fps / 60fps, 640*360@25fps / 30fps
H.264 Frame Rate 1920*1080@25fps / 30fps, 1280*720@50fps / 60fps, 640*360@25fps / 30fps
Exposure Auto
White Balance Auto
Shutter 1/25(1/30)s to 1/20,000s
Slow Shutter N.A.
Denoising 2D/3D noise reduction
Image Features Brightness, Contrast, Sharpness, Saturation,Flip, Mirror
Day/Night Switch Manual or IR-CUT filter with external trigger
Lens & IR-CUT
Lens Support M12*0.5 or M16*0.5 depend on lens mount
Lens Mount with IR-CUT MTV12 or MTV16
Mounting Hole 2 screw holes with diameter of 2.2mm,20mm Center-to-Center Spacing
Interface
Connector MX1.25*4,USB2.0 Interface
Communication Interface USB2.0,UVC Protocol
IR-CUT Control IR-CUT motor control, 3.3VDC
Day/Night External Trigger 3.3VDC to 5VDC compatibility
General
Operating Conditions -10℃~60℃, Humidity 95% or less, non-condensing
Power Supply 5VDC
Power Consumption 5VDC,1.5W without IRCUT,2W when Drive IRCUT
Dimension 38mm*38mm*10mm(not include lens and lens mount)

4 Interface & Pin list

 
CS-USB-IMX307 TOP VIEW
 
CS-USB-IMX307 BOTTOM INTERFACE
 
CS-USB-IMX307-V2.0 TOP VIEW
 
CS-USB-IMX307-V2.0 BOTTOM INTERFACE
J1:USB2.0 Interface
Pin NO. NAME Remarks
1 VBUS(5VDC) from USB HOST
2 D-
3 D+
4 GND
CS-USB-IMX307-V2.0 only have
J14:Micro B USB2.0 Interface
Pin NO. NAME Remarks
1 VBUS(5VDC) from USB HOST
2 D-
3 D+
4 GND
5 ID NC
J3:Power Input, Used during firmware upgrade
Pin NO. NAME Remarks
1 5VDC 5V IN
2 NC
3 NC
4 GND
J4:Day/Night External Trigger
Pin NO. NAME Remarks
1 IR LED ON INPUT,ACTIVE LOW
2 GND
3 RESERVE
J6:IRCUT Control
Pin NO. NAME Remarks
1 IRCUT1
2 IRCUT2
J6 IRCUT Control Functional specifications
MODE pin Signal polarity Image type Filter position
Mode 1 IRCUT1 + color Infrared cutoff
IRCUT2 -
Mode 2 IRCUT1 - mono Full wavelength pass
IRCUT2 +
J7:Configurable GPIO ( RESERVE )
Pin NO. NAME Remarks
1 GPIO0 Can Be Configured
2 GND
3 GPIO1 Can Be Configured

5 Board Dimension

 
CS-USB-IMX307 CAD drawing / unit : mm

Download dwg file here

 
CS-USB-IMX307-V2.0 CAD drawing / unit : mm

Download dwg file here

6 PCBA 3D STP File

download 3D STP file