Difference between revisions of "Camera module Stream Mode manual"

From wiki_veye
Jump to navigation Jump to search
(Created page with " <br />")
 
 
(9 intermediate revisions by 3 users not shown)
Line 1: Line 1:
  
 +
[[Camera module Stream Mode manual/zh|查看中文]]
 +
===Applicable Product models===
 +
CS-MIPI-IMX307
 +
===The concept of image synchronization mode===
 +
====free running====
 +
In this mode, the camera module runs on its own.
 +
====stream sync mode====
 +
One camera module is configured in master mode, and the other camera modules are configured in slave mode.
  
 +
The camera module in master mode outputs XVS and XHS signals, while the camera module in slave mode follows the master module for exposure and output data.
  
<br />
+
In this mode, the exposure parameters of the camera module can be configured manually or automatically.
 +
===Hardware connection of sync mode===
 +
According to the following config method, J7-3 is used as the XVS signal and J7-1 as the XHS signal.(note: In version LV3.3, XHS signals no longer need to be connected)
 +
 
 +
XVS time sequence diagram:[[File:XVS Timeing.png|alt=XVS time sequence diagram|center|thumb|800x800px|XVS timing sequence diagram]]
 +
====The method of connecting two cameras====
 +
[[File:CS-MIPI-IMX307双模组同步示意图.png|alt=CS-MIPI-IMX307双模组同步示意图|thumb|800x800px|CS-MIPI-IMX307 2 cameras sync mode(note: In version LV3.3, XHS signals no longer need to be connected) |center]]
 +
=====Jetson nano B01 config=====
 +
Reference link:[[CS-MIPI-X i2c/zh|cs_mipi_i2c.sh usage]]
 +
 
 +
*set cam0 as master
 +
 
 +
<code>./cs_mipi_i2c.sh -w -f streammode -p1 1 -p2 0 -b 7</code>
 +
 
 +
*set cam1 as slave
 +
 
 +
<code>./cs_mipi_i2c.sh -w -f streammode -p1 1 -p2 1 -b 8</code>
 +
====Jetson TX2/Xavier 6 cameras sync mode connection and configration====
 +
[[File:ADP-N1-6CAM YT0.95-4I.jpg|alt=6cam interposer board connected with 6 cameras|thumb|800x800px|6cam interposer board connected with 6 cameras|center]]<br />
 +
=====Jetson TX2/Xavier config=====
 +
Reference link:[[CS-MIPI-X i2c/zh|cs_mipi_i2c.sh usage]]
 +
 
 +
*set cam0 as master
 +
 
 +
<code>./cs_mipi_i2c.sh -w -f streammode -p1 1 -p2 0 -b 30</code>
 +
 
 +
*set other 5 cameras as slave
 +
 
 +
<code>./cs_mipi_i2c.sh -w -f streammode -p1 1 -p2 1 -b 31</code>
 +
 
 +
<code>./cs_mipi_i2c.sh -w -f streammode -p1 1 -p2 1 -b 32</code>
 +
 
 +
<code>./cs_mipi_i2c.sh -w -f streammode -p1 1 -p2 1 -b 33</code>
 +
 
 +
<code>./cs_mipi_i2c.sh -w -f streammode -p1 1 -p2 1 -b 34</code>
 +
 
 +
./cs_mipi_i2c.sh -w -f streammode -p1 1 -p2 1 -b 35<br />

Latest revision as of 13:52, 29 March 2021

查看中文

1 Applicable Product models

CS-MIPI-IMX307

2 The concept of image synchronization mode

2.1 free running

In this mode, the camera module runs on its own.

2.2 stream sync mode

One camera module is configured in master mode, and the other camera modules are configured in slave mode.

The camera module in master mode outputs XVS and XHS signals, while the camera module in slave mode follows the master module for exposure and output data.

In this mode, the exposure parameters of the camera module can be configured manually or automatically.

3 Hardware connection of sync mode

According to the following config method, J7-3 is used as the XVS signal and J7-1 as the XHS signal.(note: In version LV3.3, XHS signals no longer need to be connected)

XVS time sequence diagram:

XVS time sequence diagram
XVS timing sequence diagram

3.1 The method of connecting two cameras

CS-MIPI-IMX307双模组同步示意图
CS-MIPI-IMX307 2 cameras sync mode(note: In version LV3.3, XHS signals no longer need to be connected)
3.1.1 Jetson nano B01 config

Reference link:cs_mipi_i2c.sh usage

  • set cam0 as master

./cs_mipi_i2c.sh -w -f streammode -p1 1 -p2 0 -b 7

  • set cam1 as slave

./cs_mipi_i2c.sh -w -f streammode -p1 1 -p2 1 -b 8

3.2 Jetson TX2/Xavier 6 cameras sync mode connection and configration

6cam interposer board connected with 6 cameras
6cam interposer board connected with 6 cameras


3.2.1 Jetson TX2/Xavier config

Reference link:cs_mipi_i2c.sh usage

  • set cam0 as master

./cs_mipi_i2c.sh -w -f streammode -p1 1 -p2 0 -b 30

  • set other 5 cameras as slave

./cs_mipi_i2c.sh -w -f streammode -p1 1 -p2 1 -b 31

./cs_mipi_i2c.sh -w -f streammode -p1 1 -p2 1 -b 32

./cs_mipi_i2c.sh -w -f streammode -p1 1 -p2 1 -b 33

./cs_mipi_i2c.sh -w -f streammode -p1 1 -p2 1 -b 34

./cs_mipi_i2c.sh -w -f streammode -p1 1 -p2 1 -b 35