Line 95: |
Line 95: |
| |- | | |- |
| |0x03 | | |0x03 |
− | |WDR Enable | + | |DOL WDR Enable |
| |} | | |} |
| | | |
Line 192: |
Line 192: |
| <code>./veye_mipi_i2c.sh -r -f agc | | <code>./veye_mipi_i2c.sh -r -f agc |
| ./veye_mipi_i2c.sh -w -f agc -p1 [value]</code> | | ./veye_mipi_i2c.sh -w -f agc -p1 [value]</code> |
| + | 含义为增益上限 |
| {| class="wikitable" | | {| class="wikitable" |
| !value | | !value |
Line 203: |
Line 204: |
| <code>./veye_mipi_i2c.sh -r -f lowlight | | <code>./veye_mipi_i2c.sh -r -f lowlight |
| ./veye_mipi_i2c.sh -w -f lowlight -p1 [value]</code> | | ./veye_mipi_i2c.sh -w -f lowlight -p1 [value]</code> |
| + | 低照度情况下的降帧(慢快门)设置。在低照度情况下,摄像机模组可以通过配置此参数,延长曝光时间,降低帧率,达到更好的低照度效果。 |
| + | |
| + | 注意,在运动场景下不适合使用。 |
| {| class="wikitable" | | {| class="wikitable" |
| !value | | !value |
Line 281: |
Line 285: |
| <code>./veye_mipi_i2c.sh -w -f mshutter -p1 [value]</code> | | <code>./veye_mipi_i2c.sh -w -f mshutter -p1 [value]</code> |
| | | |
− | value值与曝光时间(单位:s)
| + | value值为曝光时间(单位:s) |
| | | |
− | value 大于等于0x4B则进入慢快门模式 | + | value 大于等于0x4B则进入低帧率模式 |
| {| class="wikitable" | | {| class="wikitable" |
| |+ | | |+ |
Line 416: |
Line 420: |
| |enable csi output | | |enable csi output |
| |} | | |} |
− | default: 0x0 | + | default: 0x1 |
| | | |
| Note: This is not low power mode, the camera is still working. | | Note: This is not low power mode, the camera is still working. |
| + | |
| + | =====brightness===== |
| + | <code>./veye_mipi_i2c.sh -r -f brightness</code> |
| + | |
| + | <code>./veye_mipi_i2c.sh -w -f brightness -p1 0x32</code> |
| + | |
| + | AE的目标亮度,范围[0,0x64] |
| + | |
| + | =====aespeed===== |
| + | <code>./veye_mipi_i2c.sh -r -f aespeed</code> |
| + | |
| + | <code>./veye_mipi_i2c.sh -w -f aespeed -p1 0x32 -p2 0x32</code> |
| + | |
| + | AE 调节速度p1为agc速度,p2为shutter速度,由慢到快[0,0x64] |
| + | |
| + | =====contrast===== |
| + | <code>./veye_mipi_i2c.sh -r -f contrast</code> |
| + | |
| + | <code>./veye_mipi_i2c.sh -w -f contrast -p1 0x32</code> |
| + | |
| + | 图像对比度,范围[0,0xFF],默认为0x80 |
| + | |
| + | =====saturation===== |
| + | <code>./veye_mipi_i2c.sh -r -f saturation</code> |
| + | |
| + | <code>./veye_mipi_i2c.sh -w -f saturation -p1 0x32</code> |
| + | |
| + | 饱和度,范围: [0,0x64] |
| + | |
| + | ===== sharppen ===== |
| + | <code>./veye_mipi_i2c.sh -r -f sharppen</code> |
| + | |
| + | <code>./veye_mipi_i2c.sh -w -f sharppen -p1 [val1] -p2 [value]</code> |
| + | {| class="wikitable" |
| + | !param1 value |
| + | !description |
| + | |- |
| + | |0x0 |
| + | |sharppen disable |
| + | |- |
| + | |0x1 |
| + | |sharppen enable |
| + | |} |
| + | default: 0x1 |
| + | |
| + | param2: sharppen strength, range [0x0-0xA] |
| + | |
| + | =====wdrtargetbr===== |
| + | <code>./veye_mipi_i2c.sh -r -f wdrtargetbr</code> |
| + | |
| + | <code>./veye_mipi_i2c.sh -w -f wdrtargetbr -p1 0x80</code> |
| + | |
| + | 宽动态模式下的整体亮度目标值。 |
| + | |
| + | WDR模式生效,[0-0xFF]默认值0x80,WDR模式下,值越大,亮度越高。 |
| + | |
| + | =====wdrbtargetbr===== |
| + | <code>./veye_mipi_i2c.sh -r -f wdrbtargetbr</code> |
| + | |
| + | <code>./veye_mipi_i2c.sh -w -f wdrbtargetbr -p1 0x80</code> |
| + | |
| + | 宽动态模式下的亮区亮度目标值。 |
| + | |
| + | WDR模式生效,[0-0xFF],默认值为0x30,值越大,亮区越亮。 |
| + | |
| + | 此参数的效果与实际场景有关,会存在一个[0-X]的无效区,X与实际场景有关。 |
| + | |
| + | 并不是说调整为0,则亮区会变黑。 |
| + | |
| + | <br /> |