Line 95: |
Line 95: |
| |- | | |- |
| |0x03 | | |0x03 |
− | |WDR Enable | + | |DOL WDR Enable |
| |} | | |} |
| =====videoformat===== | | =====videoformat===== |
Line 188: |
Line 188: |
| <code>./veye_mipi_i2c.sh -r -f agc | | <code>./veye_mipi_i2c.sh -r -f agc |
| ./veye_mipi_i2c.sh -w -f agc -p1 [value]</code> | | ./veye_mipi_i2c.sh -w -f agc -p1 [value]</code> |
| + | agc indicated max gain of AE mode. |
| {| class="wikitable" | | {| class="wikitable" |
| !value | | !value |
Line 198: |
Line 199: |
| <code>./veye_mipi_i2c.sh -r -f lowlight | | <code>./veye_mipi_i2c.sh -r -f lowlight |
| ./veye_mipi_i2c.sh -w -f lowlight -p1 [value]</code> | | ./veye_mipi_i2c.sh -w -f lowlight -p1 [value]</code> |
| + | In the case of low illuminance, the camera module can prolong the exposure time and reduce the frame rate by configuring this parameter to achieve a better effect of low illuminance. |
| + | |
| + | Note that it is not suitable for use in a sports scene. |
| {| class="wikitable" | | {| class="wikitable" |
| !value | | !value |
Line 277: |
Line 281: |
| value is exposure time(seconds) | | value is exposure time(seconds) |
| | | |
− | If value is greater than or equal to 0x4B, it enters slow shutter mode. | + | If value is greater than or equal to 0x4B, it will reduce framerate. |
| {| class="wikitable" | | {| class="wikitable" |
| |+ | | |+ |
Line 409: |
Line 413: |
| | | |
| Note: This is not low power mode, the camera is still working. | | Note: This is not low power mode, the camera is still working. |
| + | =====brightness===== |
| + | <code>./veye_mipi_i2c.sh -r -f brightness</code> |
| + | |
| + | <code>./veye_mipi_i2c.sh -w -f brightness -p1 0x32</code> |
| + | |
| + | AE Target Brightness,rang: [0,0x64] |
| + | =====aespeed===== |
| + | <code>./veye_mipi_i2c.sh -r -f aespeed</code> |
| + | |
| + | <code>./veye_mipi_i2c.sh -w -f aespeed -p1 0x32 -p2 0x32</code> |
| + | |
| + | AE adjust speed,p1 is agc speed, p2 is shutter speed,Slow to Fast: [0,0x64] |
| + | =====contrast===== |
| + | <code>./veye_mipi_i2c.sh -r -f contrast</code> |
| + | |
| + | <code>./veye_mipi_i2c.sh -w -f contrast -p1 0x32</code> |
| + | |
| + | Contrast,range: [0,0xFF],default: 0x80. |
| + | |
| + | =====saturation===== |
| + | <code>./veye_mipi_i2c.sh -r -f saturation</code> |
| + | |
| + | <code>./veye_mipi_i2c.sh -w -f saturation -p1 0x32</code> |
| + | |
| + | Saturation, range: [0,0x64]. |
| + | |
| + | ===== sharppen ===== |
| + | <code>./veye_mipi_i2c.sh -r -f sharppen</code> |
| + | |
| + | <code>./veye_mipi_i2c.sh -w -f sharppen -p1 [val1] -p2 [value]</code> |
| + | {| class="wikitable" |
| + | !param1 value |
| + | !description |
| + | |- |
| + | |0x0 |
| + | | sharppen disable |
| + | |- |
| + | |0x1 |
| + | | sharppen enable |
| + | |}default: 0x1 |
| + | |
| + | param2: sharppen strength, range [0x0-0xA] |
| + | =====wdrtargetbr===== |
| + | <code>./veye_mipi_i2c.sh -r -f wdrtargetbr</code> |
| + | |
| + | <code>./veye_mipi_i2c.sh -w -f wdrtargetbr -p1 0x80</code> |
| + | |
| + | The overall AE target value in WDR mode. |
| + | |
| + | Takes effect in WDR mode. range: [0-0xFF], default : 0x80. |
| + | =====wdrbtargetbr===== |
| + | <code>./veye_mipi_i2c.sh -r -f wdrbtargetbr</code> |
| + | |
| + | <code>./veye_mipi_i2c.sh -w -f wdrbtargetbr -p1 0x80</code> |
| + | |
| + | The AE target value of the bright area in WDR mode. |
| | | |
| + | Takes effect in WDR mode. range: [0-0xFF], default : 0x80. |
| <br /> | | <br /> |