2,021
edits
Changes
Jump to navigation
Jump to search
Line 23:
Line 23: − <br />+ − <br />+ + + − + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +
CS-FPD-CAM for Raspberry Pi (view source)
Revision as of 10:08, 4 November 2020
, 10:08, 4 November 2020→RaspberryPi System Setup and Configuration
== RaspberryPi System Setup and Configuration ==
== RaspberryPi System Setup and Configuration ==
Completely consistent with : [[CS-MIPI-X for Raspberry Pi#RaspberryPi System Setup and Configuration|RaspberryPi System Setup and Configuration]].
== Sofware Toolkits Install ==
== Sofware Toolkits Install ==
Completely consistent with : [[CS-MIPI-X for Raspberry Pi#Sofware Toolkits Install|Sofware Toolkits Install]].
In addition, we provide a FPD-Link III script for configuring the FPD-Link board.
== FPD-Link III shell script manual ==
== FPD-Link III shell script manual ==
<br />
On Raspberry PI, you need to configure I2C pins, please refer to: [[CS-MIPI-X i2c#RaspberryPi Only.2C Set IO config|raspberry pie pin configuration]] part2, and then do the following.
===fpdlink3_i2c.sh Usage===
$ ./fpdlink3_i2c.sh
Usage: ./fpdlink3_i2c.sh [-f] function name -b bus -p port -p1 param1 -p2 param2 -p3 param3
options:
-f [function name] function name
-b [i2c bus num] i2c bus number
-p [fpdlink port] fpd link port number [0,1]
-p1 [param1] param1 of each function
-p2 [param1] param2 of each function
-p3 [param1] param3 of each function
support functions: rpi_init,sync_init,trigger_init
'''fpdlink port：[[FPD-LINK3-2RX Data Sheet index|FPD-LINK3-2RX]] board，J3 is fpllink port 0, J4 is fpdlink port 1.'''
===fpdlink3_i2c.sh usage details===
=====rpi_init=====
<code>./fpdlink3_i2c.sh -f rpi_init -p 0/1</code>
init the FPD-Link channel of port0/1，'''must run this command before you can connect video and i2C.'''
=====sync_init=====
<code>./fpdlink3_i2c.sh -f sync_init -p 0 -p1 0</code>
Configure port 0 as the master of sync mode.
Connect J1 signal of [[FPD-LINK3-TX Data Sheet index|FPD-LINK3-TX]] on port 0 to J6 of [[FPD-LINK3-2RX Data Sheet index|FPD-LINK3-2RX]],direction is TX-->RX.
<code>./fpdlink3_i2c.sh -f sync_init -p 1 -p1 1</code>
Configure port 1 as the slave of sync mode.
Connect J8 signal of [[FPD-LINK3-2RX Data Sheet index|FPD-LINK3-2RX]] to J1 of [[FPD-LINK3-TX Data Sheet index|FPD-LINK3-TX]] on port 1 ,direction is RX-->TX.
=====trigger_init=====
<code>./fpdlink3_i2c.sh -f trigger_init -p 0</code>
Configure port 0 as the trigger mode.
Connect J6 signal of [[FPD-LINK3-2RX Data Sheet index|FPD-LINK3-2RX]] to J1 of [[FPD-LINK3-TX Data Sheet index|FPD-LINK3-TX]] on port 0 ,direction is RX-->TX.
<code>./fpdlink3_i2c.sh -f trigger_init -p 1</code>
Configure port 1 as the trigger mode.
Connect J8 signal of [[FPD-LINK3-2RX Data Sheet index|FPD-LINK3-2RX]] to J1 of [[FPD-LINK3-TX Data Sheet index|FPD-LINK3-TX]] on port 1 ,direction is RX-->TX.
== Typical application ==
== Typical application ==
=== CS-FPD-CAM-IMX327 Video usage ===
[[File:RaspberryPi4 connect with CS-FPD-CAM.jpg|center|thumb|600x600px|RaspberryPi4 connect with CS-FPD-CAM|link=http://wiki.veye.cc/index.php/File:RaspberryPi4_connect_with_CS-FPD-CAM.jpg]]
=====Step 1：=====
On Raspberry PI：
<code>./fpdlink3_i2c.sh -f rpi_init -p 0</code>
Init the FPD-Link channel of port0.
=====Step 2：=====
After Step 1, the stream acquisition and I2C instruction control of the camera are exactly the same as those of the camera with the MIPI interface.
*[[VEYE-MIPI-290/327 for Raspberry Pi|How to use VEYE-MIPI-X camera module on Raspberry Pi]]
*[[CS-MIPI-X for Raspberry Pi|How to use CS-MIPI-X camera module on Raspberry Pi]]
*[[CS-MIPI-X i2c|CS-MIPI-CAM I2C.sh Usage]]
*[[VEYE-MIPI-290/327 i2c/zh|VEYE-MIPI-290/327 I2C.sh Usage]]
<br />
<br />