3,108
edits
Changes
Jump to navigation
Jump to search
Line 22:
Line 22: − + Line 59:
Line 59: + + − support functions: devid,hdver,camcap,firmwarever,productmodel,videofmtcap,videofmt,ispcap,i2caddr,streammode,powerhz,+ − + − daynightmode ,hue ,contrast , satu , expostate , wbstate ,expfrmmode,expmode , aetarget, aetime,aeagc,metime ,meagain , medgain,dmetime ,dmeagain , dmedgain , awbmode , mwbcolortemp , mwbgain,imagedir,sreg,striggerone,triggeredge,autotgcnt,tgdebncr,tgdly,pickmode,pickone,mipistatus,ledstrobe,slowshuttergain,sysreboot,sysreset,paramsave − − − − Pi3B / Pi3B+ / 3A / 4B(1G/2G/4G)，we use i2c0 − − Compute Module/ CM3，we use i2c1,please add '''-b 1''' option. Line 77:
Line 72: − + Line 555:
Line 550: − + − + Line 569:
Line 564: − +
→hdver
<code>./camera_i2c_config</code>
<code>./camera_i2c_config</code>
*for RPI Computer Module
*for RPI Computer Module 3
<code>./camera_i2c_config [cameranum]</code>
<code>./camera_i2c_config [cameranum]</code>
-d [i2c addr] i2c addr if not default 0x3b
-d [i2c addr] i2c addr if not default 0x3b
=== i2c bus number on different board ===
Please refer to the following article to determine which -b parameter you need to use.
[[I2c bus number and video node|i2c bus number on different boards]]
===Functions list===
=====devid=====
=====devid=====
<code>./cs_mipi_i2c.sh -r -f devid</code>
<code>./cs_mipi_i2c.sh -r -f devid</code>
|}
|}
=====hdver=====
=====hdver=====
<code>./veye_mipi_i2c.sh -r -f hdver</code>
<code>./cs_mipi_i2c.sh -r -f hdver</code>
get hardware logic version
get hardware logic version
=====tgdebncr=====
=====tgdebncr=====
<code>./cs_mipi_i2c.sh -w -f triggeredge -p1 enable -p2 [value]</code>
<code>./cs_mipi_i2c.sh -w -f tgdebncr -p1 enable -p2 [value]</code>
<code>./cs_mipi_i2c.sh -r -f triggeredge</code><br />In Hardware Trigger mode，the debouncer attribute of the trigger signal.
<code>./cs_mipi_i2c.sh -r -f tgdebncr</code><br />In Hardware Trigger mode，the debouncer attribute of the trigger signal.
Any trigger signal that is less than value (us) will be ignored.
Any trigger signal that is less than value (us) will be ignored.
Trigger delay in Hardware Trigger mode (us).<br />note: Only CS-MIPI-SC132 Support.
Trigger delay in Hardware Trigger mode (us).<br />note: Only CS-MIPI-SC132 Support.
=====pickmode=====
=====pickmode=====
<code>./cs_mipi_i2c.sh -w -f pickmode -p1 enable</code>
<code>./cs_mipi_i2c.sh -w -f pickmode -p1 [0/1]</code>
<code>./cs_mipi_i2c.sh -r -f pickmode</code>
<code>./cs_mipi_i2c.sh -r -f pickmode</code>