Line 133: |
Line 133: |
| Writing 0 will stop the output image and enter the standby state. | | Writing 0 will stop the output image and enter the standby state. |
| | | |
− | ===== trgmode ===== | + | ===== trgmode* ===== |
| <code>./mv_mipi_i2c.sh -w -f trgmode -p1 [0,2]</code> | | <code>./mv_mipi_i2c.sh -w -f trgmode -p1 [0,2]</code> |
| | | |
Line 152: |
Line 152: |
| See product manual for details. | | See product manual for details. |
| | | |
− | ===== trgsrc ===== | + | ===== trgsrc* ===== |
| <code>./mv_mipi_i2c.sh -w -f trgsrc -p1 [0,1]</code> | | <code>./mv_mipi_i2c.sh -w -f trgsrc -p1 [0,1]</code> |
| | | |
Line 167: |
Line 167: |
| |} | | |} |
| | | |
− | ===== trgnum ===== | + | ===== trgnum* ===== |
| <code>./mv_mipi_i2c.sh -w -f trgnum -p1 [1,255]</code> | | <code>./mv_mipi_i2c.sh -w -f trgnum -p1 [1,255]</code> |
| | | |
Line 174: |
Line 174: |
| The number of image frames output by one trigger signal in trigger mode. | | The number of image frames output by one trigger signal in trigger mode. |
| | | |
− | ===== trginterval ===== | + | ===== trginterval* ===== |
| <code>./mv_mipi_i2c.sh -w -f trginterval -p1 [us]</code> | | <code>./mv_mipi_i2c.sh -w -f trginterval -p1 [us]</code> |
| | | |
Line 199: |
Line 199: |
| ==== IO Control ==== | | ==== IO Control ==== |
| | | |
− | ===== trgdelay ===== | + | ===== trgdelay* ===== |
| <code>./mv_mipi_i2c.sh -r -f trgdelay</code> | | <code>./mv_mipi_i2c.sh -r -f trgdelay</code> |
| | | |
Line 208: |
Line 208: |
| range: 0 to 1000000 (unit: microsecond) | | range: 0 to 1000000 (unit: microsecond) |
| | | |
− | ===== trgedge ===== | + | ===== trgedge* ===== |
| <code>./mv_mipi_i2c.sh -r -f trgedge</code> | | <code>./mv_mipi_i2c.sh -r -f trgedge</code> |
| | | |
Line 225: |
Line 225: |
| |} | | |} |
| | | |
− | ===== trgfilter_enable ===== | + | ===== trgfilter_enable* ===== |
| <code>./mv_mipi_i2c.sh -r -f trgfilter_enable</code> | | <code>./mv_mipi_i2c.sh -r -f trgfilter_enable</code> |
| | | |
Line 246: |
Line 246: |
| |} | | |} |
| | | |
− | ===== trgfilter_time ===== | + | ===== trgfilter_time* ===== |
| <code>./mv_mipi_i2c.sh -r -f trgfilter_time</code> | | <code>./mv_mipi_i2c.sh -r -f trgfilter_time</code> |
| | | |
Line 255: |
Line 255: |
| range: 1 to 1000000 (unit: microsecond) | | range: 1 to 1000000 (unit: microsecond) |
| | | |
− | ===== trgexp_delay ===== | + | ===== trgexp_delay* ===== |
| <code>./mv_mipi_i2c.sh -r -f trgexp_delay</code> | | <code>./mv_mipi_i2c.sh -r -f trgexp_delay</code> |
| | | |
Line 378: |
Line 378: |
| Depending on the configured ROI, the maximum frame rate will be different. This parameter supports decimals. | | Depending on the configured ROI, the maximum frame rate will be different. This parameter supports decimals. |
| | | |
− | ===== fps ===== | + | ===== fps* ===== |
| <code>./mv_mipi_i2c.sh -w -f fps -p1 [framerate]</code> | | <code>./mv_mipi_i2c.sh -w -f fps -p1 [framerate]</code> |
| | | |
Line 389: |
Line 389: |
| In video streaming mode, this parameter determines the actual frame rate. | | In video streaming mode, this parameter determines the actual frame rate. |
| | | |
− | ===== roi ===== | + | ===== roi* ===== |
| <code>./mv_mipi_i2c.sh -w -f roi -p1 [x] -p2 [y] -p3 [width] -p4 [height]</code> | | <code>./mv_mipi_i2c.sh -w -f roi -p1 [x] -p2 [y] -p3 [width] -p4 [height]</code> |
| | | |