GX-MIPI-IMX662 Data Sheet
GX-MIPI-IMX662 Datasheet
1 Introduction
The GX-MIPI-IMX662 camera module is a new generation product from VEYE IMAGING, featuring Sony’s STARVIS 2 sensor technology.
Equipped with a high-performance built-in ISP, this module offers highly controllable image parameters, multiple operating modes, and a rich set of features, supporting video output up to 1080p@60 fps.
Its MIPI-CSI2 interface enables rapid integration into embedded (AI) systems, eliminating the need for complex ISP tuning.
Designed as a compact single-board module (38 mm × 38 mm), it uses a 22-pin FPC connector with 0.5 mm pitch, allowing easy connection to popular embedded (AI) platforms such as Raspberry Pi, NVIDIA Jetson series, and Rockchip RK3588.
2 Thechnical Detail
| Thechnical Detail | |
| Sensor | |
| Sensor | SONY IMX662-AAQR-C STARVIS2 |
| Pixels | 2.07M pixel |
| Resolution | 1920*1080 |
| Image Size | Diagonal 6.45 mm (Type 1/2.8) |
| Unit Cell Size | 2.9um (H)*2.9um(V) |
| Shutter Type | Rolling Shutter |
| SNR1s Value | 0.18 |
| ISP | |
| Frame Rate | 1920*1080@60fps(max) |
| Exposure | Auto or Manual |
| White Balance | Auto or Manual |
| Shutter | 1/fps to 1/50,000s |
| Framerate | 0.065 - 60 fps |
| Slow Shutter | Auto Slow Shutter control |
| ISP | sharpening, 2D/3D noise reduction, anti-flicker, lens distortion correction,
defogging, gamma adjustment, and Dynamic Range Compression (DRC) |
| Image Setting | Brightness, Contrast, Sharpness, Saturation,Flip, Mirror |
| Day/Night Switch | Manual or IR-CUT filter with external trigger |
| Work Mode | |
| Work Mode | Video streaming mode（Free Running）, Normal Trigger Mode, Sync Mode |
| Trigger Source | Hardware，Software |
| Trigger Paramters | Trigger Polarity Control，Trigger Delay |
| Strobe Control | Strobe Output Control，Strobe Delay |
| Lens & IR-CUT | |
| Lens | MTV12 / MTV16 / CS |
| Lens Mount | M12*P0.5 / M16*P0.5 / CS，IRCUT is optional |
| Mounting Hole | 2 screw holes with diameter of 2.2mm,20mm Center-to-Center Spacing |
| Interface | |
| Connector | 22Pin 0.5mm pitch FPC, upper contact |
| I2C | Compatible with 1.8V/3.3V DC |
| Video Data Interface | MIPI CSI-2 Standard，2 Data Lane + 1 Clk Lane
UYVY / YUYV format YUV422-8bit Data Type, Bandwidth 1.188Gbps MIPI CSI-2 DC Specifications |
| IR-CUT Control | IR-CUT motor control, 3.3VDC |
| Day/Night External Trigger | 3.3VDC to 12VDC compatibility |
| General | |
| Operating Conditions
(Bare PCB) |
Performance guarantee temperature：-10℃~60℃, Humidity 95% or less, non-condensing
Operating guarantee temperature：-30℃~70℃, Humidity 95% or less, non-condensing |
| Power Supply | 5V DC |
| Power Consumption | Idle state (no image capture): 0.55 W
1080p @ 30 fps mode: 1.05 W 1080p @ 60 fps mode: 1.50 W Note: Add 0.6 W upon the IRCUT switching instant. |
| Dimension | 38mm*38mm*8.2mm(not include lens and lens mount) |
3 Spectral Sensitivity Characteristics
| Sensor | Spectral Sensitivity |
| IMX662-AAQR-C |
4 Connector Pinlist
| J3:CSI-2 Interface | ||
| Pin NO. | NAME | Remarks |
| 1 | NC | |
| 2 | SDA | 1.8V / 3.3V Level |
| 3 | SCL | 1.8V / 3.3V Level |
| 4 | GND | |
| 5 | NC | |
| 6 | SYS_RSTn | Active Low，reset camera module |
| 7 | GND | |
| 8 | NC | |
| 9 | NC | |
| 10 | GND | |
| 11 | NC | |
| 12 | NC | |
| 13 | GND | |
| 14 | MIPI_CK_P | |
| 15 | MIPI_CK_N | |
| 16 | GND | |
| 17 | MIPI_L1_P | |
| 18 | MIPI_L1_N | |
| 19 | GND | |
| 20 | MIPI_L0_P | |
| 21 | MIPI_L0_N | |
| 22 | GND | |
| J2 : Day/Night External Trigger | ||
| Pin NO. | NAME | Remarks |
| 1 | Day&Night Signal In | INPUT，Active Low（Image to MONO），3.3VDC to 12VDC compatibility |
| 2 | GND | |
| 3 | NC | |
| J4 : IRCUT Control Functional specifications | |||||
| MODE | Pin NO. | PIN NAME | Signal polarity | Image type | Filter position |
| Mode 1 | 1 | IRCUT1 | - | color | Infrared cutoff |
| 2 | IRCUT2 | + | |||
| Mode 2 | 1 | IRCUT1 | + | mono | Full wavelength pass |
| 2 | IRCUT2 | - | |||
| J6：5VDC INPUT | ||
| Pin NO. | PIN NAME | Remarks |
| 1 | 5VDC | |
| 2 | GND | |
| J7：Trigger/Sync Pin | ||
| Pin NO. | PIN NAME | Remarks |
| 1 | TRIGGER / VSYNC | Normal trigger mode: trigger signal input;
Synchronous mode(Master): synchronization signal output; Synchronous mode(Slave): synchronization signal input. |
| 2 | GND | |
| 3 | OUT1 | Output signal : Strobe signal or TriggerWait signal. |
