ADP-MV2 Adapter Board Data Sheet/zh
Jump to navigation
Jump to search
Adapter Board:ADP-MV2 DATA SHEET
转接板:ADP-MV2数据手册
1 Introduction 产品介绍
ADP-MV2是一款转接板，可将MV系列和RAW系列FFC接口转换为Firefly开源团队 ROC-RK35xx-PC 30Pin Camera接口。
ADP-MV2 is an adapter board that can convert the FFC interfaces of MV series and RAW series cameras to the Firefly open source team ROC-RK35xx-PC 30-pin camera interface.
2 Product Picture 产品图片
| PART NUMBER / 型号 | FRONT VIEW / 正面图片 | BACK VIEW / 背面图片 | Camera Support / 适配摄像机模组 |
| ADP-MV2 | MV-MIPI-IMX178M |
3 Board Pinlist 引脚说明
| J2：Down contact，30Pin 20cm FFC，connect with Firefly 30Pin FPC connector
J2：下接触，标配30Pin 20cm同面FFC，与Firefly 30Pin 接口FPC座互联 | ||
| Pin NO. 引脚号 | NAME 名称 | Remarks 说明 |
| 1 | SDA | 1.8V |
| 2 | SCL | 1.8V |
| 3 | PDN_CAM | 1.8V |
| 4 | NC | |
| 5 | GND | |
| 6 | NC | |
| 7 | NC | |
| 8 | NC | |
| 9 | NC | |
| 10 | GND | |
| 11 | MIPI_L0_P | |
| 12 | MIPI_L0_N | |
| 13 | GND | |
| 14 | MIPI_L1_P | |
| 15 | MIPI_L1_N | |
| 16 | GND | |
| 17 | MIPI_CK_P | |
| 18 | MIPI_CK_N | |
| 19 | GND | |
| 20 | NC | |
| 21 | NC | |
| 22 | GND | |
| 23 | NC | |
| 24 | NC | |
| 25 | GND | |
| 26 | NC | |
| 27 | NC | |
| 28 | GND | |
| 29 | VCC5V | POWER IN, DC5V |
| 30 | VCC5V | POWER IN, DC5V |
| J2：Up Contact, Connect to MV-MIPI-XXX Industry Camera J3
J2: 上接触，连接MV-MIPI-XXX系列工业相机 J3 | ||
| Pin NO. 引脚号 | NAME 名称 | Remarks 说明 |
| 1 | GND | |
| 2 | VCC | 5V |
| 3 | VCC | 5V |
| 4 | VCC | 5V |
| 5 | VCC | 5V |
| 6 | GND | |
| 7 | ENABLE | Camera Power Enable |
| 8 | GND | |
| 9 | MIPI_L0_N | Lane 0 Negative |
| 10 | MIPI_L0_P | Lane 0 Positive |
| 11 | GND | |
| 12 | MIPI_L1_N | Lane 1 Negative |
| 13 | MIPI_L1_P | Lane 1 Positive |
| 14 | GND | |
| 15 | MIPI_CK_N | CLK Negative |
| 16 | MIPI_CK_P | CLK Positive |
| 17 | GND | |
| 18 | MIPI_L2_N | Reserved 预留 |
| 19 | MIPI_L2_P | Reserved 预留 |
| 20 | GND | |
| 21 | MIPI_L3_N | Reserved 预留 |
| 22 | MIPI_L3_P | Reserved 预留 |
| 23 | GND | |
| 24 | SCL_MV | I2C SCL, 3.3V Level |
| 25 | SDA_MV | I2C SDA, 3.3V Level |
| 26 | GPIO3 | Reserved 预留 |
| 27 | USER IO2 | Multi-function Port 2，3.3V level；可配置输出2，3.3V电平标准 |
| 28 | USER IO1 | Multi-function Port 1，3.3V level；可配置输出1，3.3V电平标准 |
| 29 | TRIGGER_I | Hardware Trigger in，3.3V level；硬件触发输入，3.3V电平标准 |
| 30 | GND | |
| J3：Auxiliary Expansion Port 1
J3：辅助扩展口1 | |||||
| Pin NO. 引脚号 | NAME 名称 | Remarks 说明 | Pin NO. 引脚号 | NAME 名称 | Remarks 说明 |
| 1 | VCC | 板内连接到 J2-2 | 2 | GND | |
| 3 | TRIGGER_I | 板内连接到 J2-29 | 4 | GND | |
| 5 | USER IO1 | 板内连接到 J2-28 | 6 | GND | |
| 7 | USER IO2 | 板内连接到 J2-27 | 8 | GND | |
| 9 | GPIO3 | 板内连接到 J2-26 | 10 | GND | |
| 11 | SDA_MV | 板内连接到 J2-25 | 12 | SCL_MV | 板内连接到 J2-24 |
| 13 | SDA_USER | 板内连接到 J1-14 | 14 | SCL_USER | 板内连接到 J1-13 |
| 注：
使用 J1-I2C ：短接11-13，同时短接12-14。 使用 其它 I2C ：断开11-13，断开12-14；SDA信号连接J3-11，SCL信号连接J3-12。 | |||||
| Links 相关链接：
mv_mipi_i2c.sh user guide：IO Control en | |||||
| J4：Auxiliary Expansion Port 2
J4：辅助扩展口2 | ||
| Pin NO. 引脚号 | NAME 名称 | Remarks 说明 |
| 1 | VCC | 板内连接到 J2-2 |
| 2 | GND | |
| 3 | TRIGGER_I | 板内连接到 J2-29 |
| 4 | USER IO1 | 板内连接到 J2-28 |
| 5 | USER IO2 | 板内连接到 J2-27 |
| 6 | GPIO3 | 板内连接到 J2-26 |
| 7 | GND | |
| 8 | SDA_MV | 板内连接到 J2-25 |
| 9 | SCL_MV | 板内连接到 J2-24 |
| 10 | GND | |
| Links 相关链接：
mv_mipi_i2c.sh user guide：IO Control en | ||