5m mipi i2c user guide
veye5_mipi_i2c.sh user guide
1 Overview
This script is an open source program to configure the camera module by direct access to i2c registers.
Applicable models: VEYE-MIPI-IMX335
2 veye5_mipi_i2c.sh help
Usage: ./veye_mipi_i2c.sh [-r/w] [-f] function name -p1 param1 -p2 param2 -b bus
options:
-r read
-w write
-f [function name] function name
-p1 [param1] param1 of each function
-p2 [param1] param2 of each function
-b [i2c bus num] i2c bus number
-d [i2c addr] i2c addr if not default 0x3b
2.1 i2c bus
2.2 Format description
The part in square brackets [param] in the following code indicates the variable.
2.3 Details
2.4 manufacturer
./veye5_mipi_i2c.sh -r -f manufacturer
Read manufacturer information, always returns:
Manufacturer is VEYE
2.4.1 model
./veye5_mipi_i2c.sh -r -f model
Read the device model, for example: VEYE_MIPI_IMX335
2.4.2 version
./veye5_mipi_i2c.sh -r -f version
Reads the version number, for example:
control version is 01.03 , isp version 01.00
2.4.3 timestamp
./veye5_mipi_i2c.sh -r -f timestamp
Gets the time in milliseconds calculated from the moment the module starts up, incremented cyclically.
2.4.4 factoryparam
./veye5_mipi_i2c.sh -w -f factoryparam
All parameters revert to their default values.
2.4.5 paramsave
./veye5_mipi_i2c.sh -w -f paramsave
Save parameters. After all parameters are modified, this command must be executed for the parameters to be saved in flash and no longer lost when power off.
2.4.6 reboot
./veye5_mipi_i2c.sh -w -f reboot
reboot the camera.
2.4.7 errcode
./veye5_mipi_i2c.sh -r -f errcode
Get the camera error code. It should be 0 normally.
2.4.8 i2caddr
./veye5_mipi_i2c.sh -w -f i2caddr -p1 [new i2caddr] -d [old i2c addr]
./veye5_mipi_i2c.sh -r -f i2caddr -d [current i2c addr]
The camera i2c address,run paramsave and reboot to takes effect .
2.4.9 i2cport
./veye5_mipi_i2c.sh -w -f i2cport -p1 [i2c port]
./veye5_mipi_i2c.sh -r -f i2cport
The camera i2c port,run paramsave and reboot to takes effect .
| value | description | Interface Position |
|---|---|---|
| 0x00 | use i2c port on FFC cable | VEYE-MIPI-IMX335：J1 IIC |
| 0x01 | use alternate i2c port | VEYE-MIPI-IMX335：J5 IIC AUX |
2.4.10 daynightmode
./veye5_mipi_i2c.sh -w -f daynightmode -p1 [0,2]
./veye5_mipi_i2c.sh -r -f daynightmode
Day and night mode configuration
| value | description |
|---|---|
| 0x00 | Color mode |
| 0x01 | White and Black mode |
| 0x02 | Trigger mode |
2.4.11 ircutdir
./veye5_mipi_i2c.sh -w -f ircutdir -p1 [0,1]
./veye5_mipi_i2c.sh -r -f ircutdir
Controls whether the IRCUT control pin level reverse.
| value | description |
|---|---|
| 0x00 | Default direction |
| 0x01 | Reverse IRCUT control pin level |
2.4.12 irtrigger
./veye5_mipi_i2c.sh -w -f irtrigger -p1 [0,1]
./veye5_mipi_i2c.sh -r -f irtrigger
Trigger signal high and low level configuration in Trigger mode.
| value | description |
|---|---|
| 0x00 | Low level for black and white mode, high level for color mode. |
| 0x01 | Low level for color mode, high level for black and white mode. |
2.4.13 sensor_reg
./veye5_mipi_i2c.sh -r -f sensor_reg -p1 [sensor reg addr]
Read sensor register.
2.4.14 videomode
./veye5_mipi_i2c.sh -w -f videomode -p1 [video mode]
./veye5_mipi_i2c.sh -r -f videomode
Camera resolution configuration.
| value | description |
|---|---|
| 0x01 | 2592x1944@20fps |
| 0x02 | 2592x1944@12.5fps |
| 0x03 | 2560x1440@25fps |
| 0x04 | 2560x1440@30fps |
2.4.15 test_pattern
./veye5_mipi_i2c.sh -w -f test_pattern -p1 [test_enable] -p2 [type]
./veye5_mipi_i2c.sh -r -f test_pattern
Image test mode configuration.
2.4.16 awb_mode
./veye5_mipi_i2c.sh -w -f awb_mode -p1 [0,1]
./veye5_mipi_i2c.sh -r -f awb_mode
AWB mode configuration.
| value | description |
|---|---|
| 0x00 | auto |
| 0x01 | oneset，write once to trigger a white balance operation |
2.4.17 antiflicker
./veye5_mipi_i2c.sh -w -f antiflicker -p1 [0,1]
./veye5_mipi_i2c.sh -r -f antiflicker
Whether the anti-flicker function is on or not.
2.4.18 agc_max
./veye5_mipi_i2c.sh -w -f agc_max -p1 [0,0xf]
./veye5_mipi_i2c.sh -r -f agc_max
The upper limit of the auto gain function.
2.4.19 ae_target
./veye5_mipi_i2c.sh -w -f ae_target -p1 [0,0x64]
./veye5_mipi_i2c.sh -r -f ae_target
The target brightness of the automatic exposure.
2.4.20 ae_speed
./veye5_mipi_i2c.sh -w -f ae_speed -p1 [0,0x64]
./veye5_mipi_i2c.sh -r -f ae_speed
The adjustment speed of automatic exposure.
2.4.21 agc_speed
./veye5_mipi_i2c.sh -w -f agc_speed -p1 [0,0x64]
./veye5_mipi_i2c.sh -r -f agc_speed
The adjustment speed of auto gain.
2.4.22 exp_val
./veye5_mipi_i2c.sh -r -f exp_val
Current exposure value.
2.4.23 agc_val
./veye5_mipi_i2c.sh -r -f agc_val
Current gain value.
2.4.24 mshutter
./veye5_mipi_i2c.sh -w -f mshutter -p1 [0,0x0B]
./veye5_mipi_i2c.sh -r -f mshutter
Whether manual exposure is on and manual exposure configuration.
#0,auto; others, manual value
2.4.25 mirrormode
./veye5_mipi_i2c.sh -w -f mirrormode -p1 [0,0x03]
./veye5_mipi_i2c.sh -r -f mirrormode
Video flip configuration.
| value | description |
|---|---|
| 0x00 | Normal |
| 0x01 | Mirror |
| 0x02 | V-flip |
| 0x03 | Mirror and V-flip |
2.4.26 denoise_2d
./veye5_mipi_i2c.sh -w -f denoise_2d -p1 [0,0x3]
./veye5_mipi_i2c.sh -r -f denoise_2d
2D noise reduction intensity.
2.4.27 denoise_3d
./veye5_mipi_i2c.sh -w -f denoise_3d -p1 [0,0x3]
./veye5_mipi_i2c.sh -r -f denoise_3d
3D noise reduction intensity.
2.4.28 sharppen
./veye5_mipi_i2c.sh -w -f sharppen -p1 [0,0x0f]
./veye5_mipi_i2c.sh -r -f sharppen
Sharpening intensity configuration.
| value | description |
|---|---|
| 0x00 | close |
| 0x09 | low |
| 0x0B | middle |
| 0x0C | high |