CS-MIPI-IMX307 STARVIS Module
Jump to navigation
Jump to search
The printable version is no longer supported and may have rendering errors. Please update your browser bookmarks and please use the default browser print function instead.
1 Introduction
CS-MIPI-IMX307 is a highly cost-effective CSI-2 (MIPI) interface camera module, using SONY STARVIS IMX307 image sensor,
built-in excellent ISP image processing, convenient for customers to quickly integrate and release products.
2 Features
- SONY IMX307 STARVIS Sensor, 1/2.8 inch 2 Mega
- Built-in ISP processing
- CSI-2 Interface
- Uncompressed UYVY format, YUV422-8bit
- Standard lens mount
- IR-CUT circuit
- BLC, Digtal WDR, 2D/3D noise reduction, Anti-fog
- Brightness, Contrast, Sharpness, Saturation adjustable
- Framerate Continuously Adjustable
- Support Multi-camera Module Video Stream Synchronization
- Support firmware upgrade via USB disk
- Support Raspberry PI Platform,RK3399, NVIDIA JETSON Platform
3 Technical Detail
Technical Details | |
SENSOR | |
Sensor | SONY IMX307LQD-C STARVIS |
Pixels | 2.07M pixels |
Resolution | 1920*1080 |
Image Size | Diagonal 6.46 mm (Type 1/2.8) |
Unit Cell Size | 2.9um (H)*2.9um(V) |
Output Format | Bayer |
Shutter Type | Rolling Shutter |
SNR1s Value | 0.24lx |
ISP | |
Frame Rate | 1920*1080@max25fps / 30fps,
1280*720p@max50fps / 60fps(cropping mode) 640*480@max130fps(cropping mode) |
Frame Rate Adjustment | Framerate Continuously Adjustable |
Exposure | Auto or Manual |
White Balance | Auto or Manual |
Shutter | 1/25(1/30)s to 1/20,000s |
Slow Shutter | Support |
Denoising | 2D/3D noise reduction |
Image Setting | Brightness, Contrast, Sharpness, Gamma, Saturation,Flip, Mirror |
Image Enhancement | BLC, Digtal WDR(TO DO..), Defog |
Day/Night Switch | Manual or IR-CUT filter with external trigger |
Video Stream Synchronization | Support Multi-camera Module Video Stream Synchronization |
Other Functions | Pick Mode:Pick Picture from Video Stream |
Lens & IR-CUT | |
Lens | MTV12 / MTV16 / CS |
Lens Mount | M12*P0.5 / M16*P0.5 / CS,IRCUT is optional |
Mounting Hole | 2 screw holes with diameter of 2.2mm,20mm Center-to-Center Spacing |
Interface | |
Connector | 15PIN FPC, Compatible with Raspberry PI,JETSON NANO |
Communication Interface | IIC, 3.3VDC |
Video Data Interface | CSI-2 : 2 Data Lanes, CSI-2 YUV422-8bit Data Type, Datarate=594Mbps/lane |
IR-CUT Control | IR-CUT motor control, 3.3VDC |
Day/Night External Trigger | 3.3VDC to 5VDC compatibility |
General | |
Operating Conditions
(Bare PCB) |
Performance guarantee temperature:-10℃~60℃, Humidity 95% or less, non-condensing
Operating guarantee temperature: -30℃~85℃, Humidity 95% or less, non-condensing |
Power Supply | 5VDC / 3.3VDC optional |
Power Consumption | 1.4W |
Dimension | 38mm*38mm*12mm(not include lens and lens mount) |
4 Spectral Sensitivity Characteristics
Sensor | Spectral Sensitivity |
IMX307LQD-C |
5 Interface & Pin list
J1 : Firmware Update | ||
Pin NO. | NAME | Remarks |
1 | VBUS(5V) | Connect the USB upgrade cable & USB disk |
2 | D- | |
3 | D+ | |
4 | GND |
J3 : Power Input | ||
Pin NO. | NAME | Remarks |
1 | VCC5V | use by default. How to use 3.3V power supply |
2 | GND |
J4 : Day/Night External Trigger | ||
Pin NO. | NAME | Remarks |
1 | IR LED ON | Input signal,Active Low(Image to MONO),3.3VDC to 12VDC compatibility |
2 | GND | |
3 | RESERVE | NC |
J6 IRCUT Control Functional specifications | |||||
MODE | Pin NO. | PIN NAME | Signal polarity | Image type | Filter position |
Mode 1 | 1 | IRCUT1 | - | color | Infrared cutoff |
2 | IRCUT2 | + | |||
Mode 2 | 1 | IRCUT1 | + | mono | Full wavelength pass |
2 | IRCUT2 | - |
J7 : Multi-function GPIO | ||
Pin NO. | NAME | Remarks |
1 | GPIO0 | Can Be Configured As Video Stream Synchronization Signal |
2 | GND | |
3 | GPIO1 | Can Be Configured As Video Stream Synchronization Signal |
J8 : CSI-2 Interface | ||
Pin NO. | NAME | Remarks |
1 | GND | |
2 | MIPI_L0_N | |
3 | MIPI_L0_P | |
4 | GND | |
5 | MIPI_L1_N | |
6 | MIPI_L1_P | |
7 | GND | |
8 | MIPI_CK_N | |
9 | MIPI_CK_P | |
10 | GND | |
11 | NC | |
12 | NC | |
13 | SCL | 3.3V Level |
14 | SDA | 3.3V Level |
15 | VCC3V3 | NC by default,How to use 3.3V power supply |