CS-MIPI-SC132 Data Sheet

From wiki_veye
Jump to navigation Jump to search

查看中文

CS-MIPI-SC132 Data Sheet

1 Introduction

CS-MIPI-SC132 is a cost-effective CSI-2 (MIPI) interface camera module that uses the SC132GS global shutter MONO CMOS sensor whice is SmartSens Technology‘s SmartGS™ series. CS-MIPI-SC132 supports trigger mode and video stream mode.

CS-MIPI-SC132 TOP
CS-MIPI-SC132 BOTTOM

2 Features

  • 1/4 inch 1.3m pixel SmartGS™ CMOS sensor
  • Only mono mode is supported
  • Global shutter
  • Built-in ISP image processing
  • CSI-2 data interface
  • Uncompressed UYVY data format, YUV422-8bit data type
  • Standard lens interface
  • Brightness and contrast can be adjusted
  • Support video stream mode
  • Support trigger mode
  • Firmware upgrade via USB flash drive
  • Support Raspberry PI Platform,RK3399, NVIDIA JETSON Platform

3 Technical Detail

Technical Details
SENSOR
Sensor SmartSens SmartGS™ SC132GS
Pixels 1.3M pixels
Resolution 1080H*1280V
Image Size 1/4"
Unit Cell Size 2.7um *2.7um
Output Format RAW MONO
Shutter Type Global shutter
ISP
Frame Rate 1280*1080@45fps,1280*720@60fps, 640*480@120fps

1080*1280@45fps, 720*1280@60fps, 480*640@120fps

Exposure Auto or Manual
Gain Auto or Manual
Shutter ( 0 - 1 / Frame Rate ) second
Image Setting Brightness, Contrast, Gamma, Flip, Mirror
Image Synchronization mode
Free-Run The sensor runs under an autonomous clock system
Soft Trigger Trigger the image by the software control register
Auto Trigger By configuring the control register, the image is automatically triggered periodically
Hardware Trigger The image is triggered by an external trigger signal
Lens
Lens MTV12 / MTV16 / CS
Lens Mount M12*P0.5 / M16*P0.5 / CS
Mounting Hole 2 screw holes with diameter of 2.2mm,20mm Center-to-Center Spacing
Interface
Connector 15PIN FPC, Compatible with Raspberry PI,JETSON NANO
Communication Interface IIC, 3.3VDC
Video Data Interface CSI-2 : 2 Data Lane,MIPI CSI-2 DC Specifications
MIPI CLK frequence 297MHz
MIPI Data bandwidth 594Mbps / lane
Data Type YUV422-8bit
General
Operating Conditions

(Bare PCB)

Performance guarantee temperature:-20℃~60℃, Humidity 95% or less, non-condensing

Operating guarantee temperature: -30℃~85℃, Humidity 95% or less, non-condensing

Power Supply 5VDC / 3.3VDC optional
Power Consumption TBD
Dimension 38mm*38mm*10mm(not include lens and lens mount)

4 Optical Quantum Efficiency

Sensor Quantum Efficiency
SC132GS
SC132GS QE

5 Interface & Pin list

CS-MIPI-SC132-TOP LAYER
File:CS-MIPI-SC132 006.jpg
CS-MIPI-SC132-BOTTOM INTERFACE
J1 : Firmware Update
Pin NO. NAME Remarks
1 VBUS(5V) Connect the USB upgrade cable & USB disk
2 D-
3 D+
4 GND
J3 : Power Input
Pin NO. NAME Remarks
1 VCC5V use by default. How to use 3.3V power supply
2 GND
J7 : Multi-function GPIO
Pin NO. NAME Remarks
1 GPIO0 Multi-function IO
2 GND
3 GPIO1 Multi-function IO
J8 : CSI-2 Interface
Pin NO. NAME Remarks
1 GND
2 MIPI_L0_N
3 MIPI_L0_P
4 GND
5 MIPI_L1_N
6 MIPI_L1_P
7 GND
8 MIPI_CK_N
9 MIPI_CK_P
10 GND
11 NC
12 NC
13 SCL 3.3V Level
14 SDA 3.3V Level
15 VCC3V3 NC by default,How to use 3.3V power supply

6 Board Dimension

CS-MIPI-SC132 CAD FILE / unit:mm

Download dwg file here