CS-MIPI-SC132 Data Sheet
Jump to navigation
Jump to search
The printable version is no longer supported and may have rendering errors. Please update your browser bookmarks and please use the default browser print function instead.
CS-MIPI-SC132 Data Sheet
1 Introduction
CS-MIPI-SC132 / CS-MIPI-SC132-V2 is a cost-effective CSI-2 (MIPI) interface camera module that uses the SC132GS global shutter MONO CMOS sensor whice is SmartSens Technology‘s SmartGS™ series. CS-MIPI-SC132 / CS-MIPI-SC132-V2 supports trigger mode and video stream mode.
2 Features
- 1/4 inch 1.3m pixel SmartGS® CMOS sensor
- Only mono mode is supported
- Global shutter
- Built-in ISP image processing
- CSI-2 data interface
- Uncompressed UYVY data format, YUV422-8bit data type
- Standard lens interface
- Brightness and contrast can be adjusted
- Support video stream mode
- Support trigger mode
- Firmware upgrade via USB flash drive
- Support Raspberry PI Platform, NVIDIA JETSON Platform
3 Technical Detail
Technical Details | |
SENSOR | |
Sensor | SmartSens SmartGS® SC132GS |
Pixels | 1.3M pixels |
Resolution | 1080H*1280V |
Image Size | 1/4" |
Unit Cell Size | 2.7um *2.7um |
Output Format | RAW MONO |
Shutter Type | Global shutter |
ISP | |
Frame Rate | 1280*1080@max45fps,1280*720@max60fps, 640*480@max120fps
1080*1280@max45fps, 720*1280@max60fps, 480*640@max120fps |
Exposure | Auto or Manual |
Gain | Auto or Manual |
Shutter | ( 0 - 1 / Frame Rate ) second |
Image Setting | Brightness, Contrast, Gamma, Flip, Mirror |
Image Synchronization mode | |
Free-Run | The sensor runs under an autonomous clock system |
Soft Trigger | The image is triggered by the DRA(Direct Register Access) |
Hardware Trigger | The image is triggered by an external trigger signal,Support multi-camera synchronization |
Lens | |
Lens | MTV12 / MTV16 / CS |
Lens Mount | M12*P0.5 / M16*P0.5 / CS |
Mounting Hole | 2 screw holes with diameter of 2.2mm,20mm Center-to-Center Spacing |
Interface | |
Connector | 15PIN FPC, Compatible with Raspberry PI,JETSON NANO |
Communication Interface | IIC, 3.3VDC |
Video Data Interface | CSI-2 : 2 Data Lane,MIPI CSI-2 DC Specifications |
MIPI CLK frequence | 297MHz |
MIPI Data bandwidth | 594Mbps / lane * 2 |
Data Type | YUV422-8bit |
General | |
Operating Conditions
(Bare PCB) |
Performance guarantee temperature:-20℃~60℃, Humidity 95% or less, non-condensing
Operating guarantee temperature: -30℃~85℃, Humidity 95% or less, non-condensing |
Power Supply | 5VDC / 3.3VDC optional,3.3V default |
Power Consumption | CS-MIPI-SC132:Rate Power 1.16W
/ CS-MIPI-SC132-V2:Rate Power 1.23W,Transient Power 1.32W |
Dimension | 38mm*38mm*12mm(not include lens and lens mount) |
4 Optical Quantum Efficiency
Sensor | Quantum Efficiency |
SC132GS |
5 Interface & Pin list
J1 : Firmware Update | ||
Pin NO. | NAME | Remarks |
1 | VBUS(5V) | Connect the USB upgrade cable & USB disk |
2 | D- | |
3 | D+ | |
4 | GND |
J3 : Power Input | ||
Pin NO. | NAME | Remarks |
1 | VCC5V | Optional power supply. How to use 5V power supply |
2 | GND |
J7 : GPIO | ||
Pin NO. | NAME | Remarks |
1 | Trigger In | Compatible with 2.5-3.3V level |
2 | GND | |
3 | Strobe Out | 2.5V level |
J14 : UART | ||
Pin NO. | NAME | Remarks |
1 | UART_TX | |
2 | GND | |
3 | UART_RX |
J8 : CSI-2 Interface | ||
Pin NO. | NAME | Remarks |
1 | GND | |
2 | MIPI_L0_N | |
3 | MIPI_L0_P | |
4 | GND | |
5 | MIPI_L1_N | |
6 | MIPI_L1_P | |
7 | GND | |
8 | MIPI_CK_N | |
9 | MIPI_CK_P | |
10 | GND | |
11 | NC | |
12 | NC | |
13 | SCL | 3.3V Level |
14 | SDA | 3.3V Level |
15 | VCC3V3 | Use by default,How to use 5V power supply |