Difference between revisions of "Mv mipi camera manual"

From wiki_veye
Jump to navigation Jump to search
Line 133: Line 133:
  
 
===== TriggerWait =====
 
===== TriggerWait =====
<br />
+
Triggerwait signal indicate that the camera is busy now,unable to respond to trigger signal,active high.
 +
 
 +
The camera's trigger wait signal can be used to optimize trigger image acquisition and can effectively avoid the problem of over-triggering.<br />
 
===== XVS =====
 
===== XVS =====
 +
Output the XVS signal of the sensor.
  
 
===== XHS =====
 
===== XHS =====
 +
Output the XVS signal of the sensor.
  
 
===== Pin Reverse =====
 
===== Pin Reverse =====
  
 
==== Read pin status ====
 
==== Read pin status ====

Revision as of 12:00, 14 March 2022

查看中文

MV series MIPI image module manual

1 Overview

MV series is a series of camera modules specially designed for machine vision. It is excellent in performance, compact and affordable in price. In addition to the video streaming mode, a trigger mode and a series of functions related to triggering are also provided. Provides a better option for embedded systems for machine vision applications.

To facilitate rapid development, we provide hardware datasheet , register manuals and drivers for embedded platforms, demos.

This article focuses on the functional principles of the MV camera in detail. For hardware manuals, registers, configuration scripts, drivers for different embedded platforms and usage, please refer to the corresponding documents.

In this article, the [Related Commands] column after each function lists the commands in the mv_mipi_i2c.sh script that are related to this function.

2 Image Acquisition

2.1 Rolling shutter and Global shutter

2.1.1 Rolling shutter

The rolling shutter sensor is implemented as shown in the figure below.。The exposure starts from the first line and the second line is exposed only after one line cycle.And so on, after N-1 rows the Nth row is exposed.It takes one cycle time to read out a row of data after the first row is exposed.After the first line is completely read out, the second line just starts to be read out. In this order, the whole image is completely read out. The rolling shutter sensors are less technically difficult than global exposure sensors, cheaper, and have greater resolution, making them a good choice for some static or slow object photography.

Rolling shutter mode
Rolling shutter mode
2.1.2 Global shutter

The global shutter sensor implementation is shown in the figure below. All rows of the sensor start exposure at the same time and end exposure at the same time. At the end of the exposure, the sensor transfers all electrons from the sensing area to the storage area and then reads out the pixel data row by row.The advantage of such exposure is that the image will not be shifted and skewed when shooting moving objects.

Global shutter mode
Global shutter mode


2.2 Start/Stop Acquisition

You can send the start acquisition and stop acquisition commands to the camera at any time.

Once the camera receives the start acquisition command, if working in video streaming mode, it will immediately start exposure and output images; if working in trigger mode, it will enter the state of waiting for the trigger signal. At the same time, the camera enters the running state.

Once the camera receives the stop acquisition command, it will complete the currently transmitting frames to ensure frame integrity, and then stop outputting images and enter the standby state. Note that the triggering process will be interrupted if triggering multiple frames is set and not all image frames have been output yet. That is, stopping the acquisition operation only guarantees the integrity of the current frame, not the entire trigger cycle.

Related commands :imgacq.

2.3 Video streaming mode

In video streaming mode, the camera continuously exposes and outputs images according to the configured ROI region and frame rate. It is recommended to get the maximum frame rate supported by the maxfps function after changing the ROI.

Related commands :trgmode,roi,fps,maxfps.

2.4 Normal trigger mode

2.4.1 Rolling shutter

For a rolling shutter sensor, such as IMX178, a complete image frame requires two image cycles to complete the process from exposure to output. So the maximum frame rate is half of the video streaming mode.

In normal trigger mode, for rolling shutter sensor, we refer to two consecutive frame cycles as one trigger cycle.

In normal trigger mode, if multiple frames are triggered at one time, the trigger delay acts after this trigger signal, and the trigger interval and exposure delay are valid before each trigger cycle.

The following figure shows an example of a trigger period with Trigger Number set to 2:

Normal trigger mode( Rolling shutter)
2.4.2 Global shutter

TODO

2.5 High-speed continuous trigger mode

2.5.1 Rolling shutter

In high-speed trigger mode, assume Trigger Number is N, frames 2 to N are output immediately after the previous frame and there is no more trigger interval. This allows the same maximum frame rate to be achieved as in video streaming mode.

The following figure shows an example of a trigger period with Trigger Number set to 3:

High-speed trigger mode(Rolling shutter)


2.6 Switching of modes

The working mode cannot be switched during operation; you must stop the acquisition before switch to a new working mode.

2.7 Trigger source

The soft trigger and hard trigger are only different in the source of trigger signal. The trigger delay, exposure delay, trigger frame number, trigger interval configurations and functions are exactly the same.

Related commands :trgsrc.

2.7.1 Software trigger mode

By writing 1 to the corresponding register of the camera via the i2c bus, a soft trigger is performed.

Since there is a certain delay in software processing and i2c transmission, the timeliness of soft trigger is worse than hard trigger , and hard trigger is recommended for the occasions with high timeliness requirements.

Related commands :trgone.

2.7.2 Hardware trigger mode

In hard trigger mode, the camera obtains the trigger signal by capturing the level change of the TrigIN IO. See the IO Control chapter for details.

2.8 Trigger statistics

The trigger statistics function counts the total number of triggers as well as the number of lost triggers.

Definition of total trigger number: in hard trigger mode, it is the number of triggers after trigger filtering; in soft trigger mode, it is the number of all triggers.

When the camera receives a trigger signal, it will not be able to respond to the new trigger signal if it is in the trigger cycle, which will cause the loss of the trigger signal.

Related commands :trgcount, trgclr.

3 Image Feature


4 ISP


5 IO Control

5.1 Input IO Configuration

Now there is only one input pin: TriggerIN_IO. The function is: input signal for hard trigger.

The active edge of the trigger signal can be configured via the Trigger Edge function.

Related commands :trgedge.

5.1.1 Trigger Filter

In order to suppress the interference in the external trigger signal, MV series cameras have external trigger filtering function, including low level filtering and high level filtering.

The function of low level filtering is to filter out the interference signal on the low level, and the function of high level filtering is to filter out the interference signal on the high level.

The range of the filtering window can be set to [1,1000000]us.

The following figure shows an example of enabling both low level filtering and high level filtering with a filtering time of 1ms:

Trigger Filter

Related commands :trgfilter_enable,trgfilter_time.

5.1.2 Trigger Delay

MV series cameras have a trigger delay function. The trigger delay time can be set to [1,1000000]us. It is in effect for both hard and soft triggers.

Related commands :trgdelay.

5.1.3 Output IO Configuration

MV series cameras now have 2 output signals, OUT_IO1 and OUT_IO2.

OUT_IO1 can be configured for Strobe and Userout functions.

OUT_IO2 can be configured for five functions, Strobe, Userout, TriggerWait, XVS and XHS.

Related commands: outio1_mode, outio2_mode.

5.1.4 Strobe

In this mode, the camera sends a trigger signal to activate the flash. Strobe signal is active high, and when the trigger signal is received, the strobe signal level is pulled up, and the pull-up time is the sum of the exposure delay and trigger cycle.

5.1.5 UserOut

In this mode users can set their own constant output level of the camera to do special processing, such as controlling the constant light source or an alarm device.

The output level can be set individually for different OUT_IO.

5.1.6 TriggerWait

Triggerwait signal indicate that the camera is busy now,unable to respond to trigger signal,active high.

The camera's trigger wait signal can be used to optimize trigger image acquisition and can effectively avoid the problem of over-triggering.

5.1.7 XVS

Output the XVS signal of the sensor.

5.1.8 XHS

Output the XVS signal of the sensor.

5.1.9 Pin Reverse

5.2 Read pin status